Heat Medium Skid
1 MMBTU/hr%u00A0
Direct Fired Heater
48" dia. x 12' horizontal shell
Insulated Exterior except Firetube head
C.W.
Expansion tank, vertical
Ladder%u00A0
External Fuel Gas and Pilot lines1 MMBTU/hr firetube c.w.
Flame Arrester, Burner, stack
Pilot and fuel gas linesCirculation System: (Dual System c.w. bypass)
Pumps:
Model SST
1-1/4 x 2-6
Impeller dia. 5.563"
Catalogue No. 4ST55013
Motors:
Baldor - Reliance
Cat. No. JML3608T
Spec. 36E510W914
Frame 184JM
TEFC Enclosure%u00A0
5 HP
230V/1/60
19.5A, 3450 rpmSkid
Skid dimensions TBD
c.w. Checker Plate floor inside enclosure
Lifting lugs under saddle extension
Interior Aluminum fluted linerEnclosure:
Dimensions TBD
Galvanized c.w. insulation
shed-type roof
Door c.w. panic bar, checkchain and threshold
Window
ventilation c.w. slides
Interior Heat medium piping is insulated and clad.Instruments and controls:
Inline 3" Y-Strainers swage to 2" pumps
PIs
Manual block valves up and downstream of each pump system
Kimray T-12 %u00A0Temperature Controller
Kimray HT 12 High tEmperture Shut Down
Kimray Drip Pot
Two Kimray Motor Valves
Three Fisher 67 AFR Regulators (TBC, or equivalent)
One Fisher 627 regulator (TBC, or equivalent)All electrical pre-wired.To be confirmed:
- in bath temperature sensor or LLSD, Electric One on head, one on shell inside buildingOriginal purpose:
Use Pump system c.w. 2" 150 RF ANSI lines to service 3" 150 RF lines for heating two tanks and three utility buildings.

Show Less

AKU/weir style shell and tube exchanger, new surplus, unused, built in 2008Originally intended for use as a Sulfinol Regeneration Reboiler, this exchanger features:Channel and Removable cover
kettle-Type Receiver
U-Tube Bundle
405 sq. m tube surface area
Shell Side Pressure: 517 kPa @ 163C, -29C
Tube Side Pressure: 1413 kPa @ 205 C, -29C
3.2 mm c.a.
Channel Head mat'l: SA-516-70N
Head mat'l: SA-516-70
Shell SA-516-70
Full RT oon Long and girth joints
PWHT @ 1125F for 30 min.
One Shell Pass
Two Tube Passes
Dimensions: 1016 mm x 1676 mm-6020mm
Horizontal c.w. saddles.
Shipping weight: 13,154 kg
AB registeredConnections:Channel Inlet: 10" 300 ANSI RFWN
Channel Outlet: 10" 300 ANSI RFWN
Shell Inlet: 12" 300 ANSI RFWN
Shell Outlets: two of 14" 300 ANSI RFWN
Drain: 10" 300 ANSI RFWN
Yokes: %u00A0two of 2" 300 ANSI RFWN
Corrosion: 2" 300 ANSI RFWN, w. blindOriginal design calculations, drawings and QC manuals on file

Show Less

Fluid / Glycol heat exchanger
Design Conditions
150 psig maximum allowable working pressure (M.A.W.P.) at 450 deg F shell side
1/16" corrosion allowance
Service - sweet
-20 deg F minimum design metal temperature (M.D.M.T.)Size
4.5" O.D. x 35'-0" Seam / SeamFeatures
- Horizontal construction
- ASME Sec.VIII Div.1 constructed with registration in Alberta, BC, SK.
- Internal bafflesNOZZLES
N1 Inlet%u00A0
1 2" CL 150 RFSO Flange
N2 Outlet%u00A0
1 2" CL 150 RFSO Flange
N3 Optional In%u00A0
1 2" CL 150 RFSO Flange
N4 Optional Out%u00A0
1 2" CL 150 RFWN FlangeMATERIAL SPECIFICATION
Fluid / Glycol Heat Exchanger
Item Material%u00A0
Schedule/ Thickness/ Rating
Shell%u00A0
SA-106B sch. std
Heads%u00A0
SA-234 WPB sch. std.
Internals%u00A0
SA-36 / 44W 1/4"
Flanges%u00A0
SA-105N CL.150 RFWN / RFSO
Nozzle Necks%u00A0
SA-106B 2" sch. STD pipe
Weld Fittings%u00A0
SA-234 WPB Sch. stdTESTING - RADIOGRAPHY - P.W.H.T.
PRESSURE TESTING
Fluid / Glycol Heat exchanger%u00A0
As per ASME Section VIII - Division 1 latest edition, UG-99(b) (i.e. 1.3 x D.P.)
Charted Hydrotest Is not included.RADIOGRAPHY
Fluid / Glycol Heat exchanger%u00A0
As per ASME Section VIII - Division 1, latest edition, UW-11(a) (i.e. RT-2 spot radiography)POST WELD HEAT TREATMENT
Fluid / Glycol Heat exchanger NONE
As per ASME Section VIII - Division 1
(i.e. 0 minutes at 1,150 degF +- 25 degF)ULTRASONIC TESTING
Fluid / Glycol Heat exchanger%u00A0
None
MAGNETIC PARTICLE INSPECTION
Fluid / Glycol Heat exchanger%u00A0
NonePAINTING AND SURFACE PREPARATION
Vessel
Surface Preparation SSPC-SP#6
Primer%u00A0
One (1) Coat EPOXY Primer
Finish Paint%u00A0
One (1) Coat Warm Grey PUNotes
Surface preparation and paint as listed will be applied to external surfaces of equipment only.
The underside of the structural skid is excluded from this specification.
Equipment mounted on skids prior to surface preparation and painting will be painted where is
(i.e. Under vessel base plates, etc. will not be painted).
Copies of AB-025 forms, name plate facsimile, MTR's, NDE reports and QC travel sheet.
One (1) set of "As-Built" drawings.an additional order volume discount of $200.- per each unit applies at each volume stage listed below:
i.e.%u00A0
5 units: an additional $200.-/ unit off per job
10 units: an additional $400.-/ unit off per job
15 units: an additional $600.-/ unit off, per job

Show Less

NEN/ style shell and tube exchanger, new surplus, unused, built in 2008Originally intended for use as a Sulphur Condenser, this exchanger features:Channel Integral with Tubesheet and Removable cover
One Pass Shell
Fixed Tubesheet Like "N" Stationary Head
Shell Side Pressure: 1413 kPa @ 204C, -29C, Single Pass
Tube Pressure: 103 kPa # 343C, Single Pass
Demister pad
3.2 mm c.a.
Cylinder mat'l: SA-516-70
Full RT on long and girth joints
PWHT @ 1125F for 30 min.
Tube Surface area: 273 sq. meter
Dimensions: 11016 mm x 1773 mm
Horizontal c.w. saddles, angled orientation
Shipping weight: 13,154 kg
AB registeredConnections:Channel Inlet: 20" 150 ANSI RFWN
Channel Outlet: 20" 150 ANSI RFWN
Shell Inlet: 8" 300 ANSI RFWN
Shell Outlets: 8" 300 ANSI RFWN
Drain: 3/4" 6000# cplg
Sulphur drain: 3" x 4"" 300 ANSI RFSO
Sulphur Pot: 20"x 24" 150 ANSI RFSO, w. blindOriginal design calculations, drawings and QC manuals on file

Show Less

Trantner Spiral Heat Exchanger
New surplus (1 of 6 available)
Diameter                            
31.5" (800 mm)
Length                                 
79" (2003 mm)
Pressure                              
355 psi (24.5 Bar)
300 ANSI flange rating
Vacuum
-14.5 psig  (-1 Bar)
Effective Surface Area      
1980 sq./ft.


Nozzle Schedule
6" inlet and outlet for stream 1
8" inlet and outlet for stream 2


Designed for:
716,7600 kg/hr produced water inlet on hot side
415,800 kg/hr fluid on cold side


Also Available:
- U1a Data report
- Vessel drawing
- Sizing Data Sheet

Show Less