100 Bbl API 12F double walled tanks including the following,
General:
9'6"D x 8'H
• 100 Bbl (64 m3) nominal capacity
• Double walled, steel tank
• 2 - lifting lugs
• Ladder w/ top loop
• Built to API 12F specs
• Steel is G40.21-04, 38W/44W, ASTM A36/ASME SA36-10/11, also meeting requirements of API 650 Group 3
• %u00BC" primary floor
• 3/16" shells, roof, and secondary floor
Nozzle Description:
• All couplings A105N 3000#
• 3 -couplings for Level gauge connection
• 8" thief hatch connection
• 3- 2" coupling
• 2- 3" couplings
• 1- 6" RFWN w/ gooseneck & birdscreen
• 24"x 36" std manway 

Show Less

New 100 bbl 10' x 8' double wall Amine tank c/w
• 16 oz/0.4 oz vac design
• built to API 650 modified code
• removable heat coil 
• Internally coated with Devchem 253
• Insulated with 1-1/2 " spray foam insulation 
• Exterior of the floor coated with coal tar epoxy

NOZZLES :
N1 -      4" 150# RFWN Flanges (Outlet)
N2 -      4" 150# RFWN Flanges (Inlet)
N3 -      2" 150# RFWN DFF Flange (pump out with internal syphon)
N4 -      2" 150# RFWN Flanges (TC)
N5a/b - 2" 150# RFWN Flange (Heat medium outlet)
N6a/b - 2" 150# RFWN Flange (level gauge)
N7 -      2" 150# RFWN Flange (TI)
N8 -      2" 150# RFWN Flange (Blanket Gas)
N9 -      3" 150# RFWN Flange (level transmitter)
N10-     2" 150# RFWN Flange (spare)
N11-     3" 150# RFWN Flange (Truck in)
TH         8" std Thief hatch opening

Show Less

100BBL single wall tank 9'6 dia x 8' High
New, surplus, never used, built in 2011
Tank Includes:
1/4" floor
3/16" walls, 2 rings, 4' wide.
A-36 Steell
M1 24" x 36" cleanout c.w. neoprene gasket
N1 8" long pan thief hatc c.w. neoprene gasket
N2 3" FNPT half cplg Fill connection
N3 3" FNPT half cplg Auxilliary connection
N4 3" FNPT half cplg Overflow connection
N5 3" FNPT half cplg overflow connection
N6 3" FNPT half cplg c.w. 3" 90 deg Ell Drain connection
N7 3" FNPT half cplg Pipe connection
N8 3" FNPT half cplg Vent connection
N9 3" FNPT half cplg spare connection
2- Lifting lugs
Bolting: ASTM A-307-00
Tank will be blasted, primed and painted and includes sweet Jayco thief hatch and
Tank weight approx.. 3700 lbs
Painted Grey, 2.0-2.5 mils DFT
Bottom coated with Asphalt
Shop Test tank by air pressure to +16 /-.5 Oz.
API 12F Monogrammed
Ladder
Thief Hatch, Std. 8"
In stock in Red Deer, AB

Show Less

 1- 100BBL single wall tank  9' dia x 8' High
Tank Includes:
N1-  4" 150 ANSI RFWN - Inlet
N2 - 4" 150 ANSI RFWN - Outlet
N3 - 3" 150 ANSI RFWN - HLSD
N4 - 2" 150 ANSI RFWN - Upper-equalizer/overflow
N5 - 2" 150 ANSI RFWN - Upper-equalizer/overflow
N6 - 8" vent 150 ANSI RFWN , c/w goose neckand bird screen
N7 - 2" 150 ANSI RFWN c/w blind flange tapped 3/4"/ 3/4" hex plug - Gauge Board connection


1- 24 x 36 manway
1- 8" Thief hatch nozzle c/w Jayco 8 oz thief hatch
1- 8' plain ladder equal length mounting brackets
1- Gauge Board
2- Lifting lugs

• 3/16" shell and roof
• Structural bottom skid


Tank will be blasted, primed and painted and includes sweet Jayco thief hatch and
Sweet service gauge board


Tank weight approx 4800 lbs

Show Less

1- 100BBL single wall tank 9' dia x 8' High
Tank Includes:
N1- 4" 150 ANSI RFWN - Inlet
N2 - 4" 150 ANSI RFWN - Outlet
N3 - 3" 150 ANSI RFWN - HLSD
N4 - 2" 150 ANSI RFWN - Upper-equalizer/overflow
N5 - 2" 150 ANSI RFWN - Upper-equalizer/overflow
N6 - 8" vent 150 ANSI RFWN , c/w goose neck and bird screen
N7 - 2" 150 ANSI RFWN c/w blind flange tapped 3/4"/ 3/4" hex plug - Gauge Board connection

1- 24 x 36 manway
1- 8" Thief hatch nozzle (thief hatch extra)
1- 8' plain ladder equal length mounting brackets
2- Lifting lugs
• 3/16" shell and roof
• Structural bottom skid

Tank will be blasted, primed and painted
Choose your desired sweet or sour service gauge board and thief hatch below

Tank weight approx 4800 lbs

Show Less

 1- 100BBL single wall tank  9' dia x 8' High
Tank Includes:
N1-  4" 150 ANSI RFWN - Inle
N2 - 4" 150 ANSI RFWN - Outlet
N3 - 3" 150 ANSI RFWN - HLSD
N4 - 2" 150 ANSI RFWN - Upper-equalizer/overflow
N5 - 2" 150 ANSI RFWN - Upper-equalizer/overflow
N6 - 8" vent 150 ANSI RFWN , c/w goose neck and bird screen
N7 - 2" 150 ANSI RFWN c/w blind flange tapped 3/4"/ 3/4" hex plug - Gauge Board connection


1- 24 x 36 manway
1- 8" Thief hatch nozzle (thief hatch extra)
1- 8' plain ladder equal length mounting brackets
2- Lifting lugs

• 3/16" shell and roof
• Structural bottom skid


Tank will be blasted, primed and painted 
Choose your desired sweet or sour service gauge board and thief hatch below


Tank weight approx 4800 lbs

Show Less

Surplus 100 Bbl Nominal Capacity tank
Built by Argo Industries
Ser. No. 1734
Design:
9'-6" dia. x 8.0' dia. approx.
External features:
- No skid
- Ladder w.o. ring
- 1 lift lug for tank itself
- Thief Hatch, 8", sweet service
- 2" NPT vent c.w. elbow
- one 2" NPT connections on side, c.w. downcomer
- one 2" NPT connections on side, c.w. gate valve and pipe c.w. 2 Ells
- Paint is in fair condition, grey with blue bottom ring and thief hatch (some bare patches on one side on blue area

Show Less

Pop tank with removable roof
100 Bbl Nominal Capacity 
Built by Marclin Industries
Ser. No. 0080


Design:
9'-6" dia. x 8.0' dia. approx.
Shell is 3/16" thick
Floor is 1/4"


External features
 No skid
 Removable roof
 Hinged manway on roof
 Ladder c.w. ring
 Top reinforcement ring
 2 lift lugs


Connections:
two 2" flanged connections on side, one blanked
two 2" NPT connections on side, one c.w. Fisher and  LC 
3" vent c.w. lift lug for roof removal
Flanged drain c.w. gate valve and camlock cplg
Paint is in poor condition, White with blue bottom ring.
Sold, as is, Exw. OilPro Blackfalds yard.

Show Less

RE: 1- 100 Bbl single wall tank 17.25 cu/m 
New, surplus
Tank description:
9'6" dia x 8' High
Floor: 3/16" A-36 plate
Shell: 3/16"
Roof: 3/16"

- 3" Collar, Vent Connection
- 3" Collar, Inlet Connection
- 3" Collar, Outlet Connection
- 2" High Level Shutdown, 12" down from shell seam

1- 24" x 36" manway
1- 8" 8 Oz thief hatch
1- gauge system
1- 8' plain ladder equal length mounting brackets
2- Lifting lugs A-36, 3" eye

Structural bottom skid
 - 4 x 2 x 0.188 HSS beams
 - 5' x 111' o/a
Tank is painted tan

Show Less

RE: 1-1000BBL single containment tank  15'3" x 32' high
Tank contains the following:
Roof 1/4" A36
Shell 1/4" A36 (first course_
Shell 3/16" A36 (remaining three courses)
Floor 1/4" A36
Built to API 650 Modified Specifications
16 ounce non-engineered design - Tested to 24 oz
Radiography at cost plus 20%
Material - API 650 Group IIIA normalized
G40.21-04 , 38W/44W, ASTM
A36/ASME SA36-10/11
MDMT -40 degrees F

NOTE:
This material has been manufactured , tested and found to meet the specifications and purchase order requirements regarding structural quality coil for conversion to:
 * CSA G40.21-04 Grade 38W/44W
 * ASTM A36
 *ASME SA36-10-11 ADD
These designations meet all the material requirements of API650 (12th Edition) Group III - Killed Fine Grain Practice

15'3" dia x 32' tall built to API 650 MODIFIED
Thief hatch flange (thief hatch options below)
Gauge board fittings and brackets (gauge board options below)
nozzles as adders (see below)
no piping included
3" threaded near ladder for HLSD
4" center roof vent c/w 180 and bird screen
24" x 48" sidewall manway
Caged Ladder (OH&S)
4 lift lugs
1 tailing lug
4 hauling pads
grounding lug

As per attached drawing OilPro Stock 1000BBL REV C
Final price to be confirmed on appoved drawings

GENERAL COMMENTS
1. The above quoted ladder assembly has been engineered to comply with OH & S -
Process Industry Practices standard STF05501 for fixed ladders and cages.
Please Note:
• 30 feet is the limit for a single ladder with cage only.
• Two options for taller ladder are:
-Multiple offset ladder sections with landings at the transition points.
-Single ladder with fall arrest system (note cage is also not required if fall arrest
system is used)
2. Roof to shell joint will be seal welded on the outside only as per API 650,
Appendix F, and Detail B. For internally coated tanks, coating of the shell to roof
joint must be grouted prior to coating and therefore grout will be used for repair of voids. (Note: This does not follow NACE RP-0178 figure A.7.)
3. We have made no provision for nozzle loading calculations.
4. We have not allowed for any engineering or drafting changes. Any changes will be
charged a rate of $90.00 per hour for drafting and $120.00 per hour for engineering
with a minimum charge of two hours per drawing affected. This will also affect the
above quoted delivery.
5. All standard accessories and appurtenances will be shipped loose unless
otherwise stated. Customer is responsible for ensuring that all connections,
including manway nuts and bolts are tightened and equipment is inspected prior to it
being put into commission.
6. Unless otherwise stated above radiography has not been included. If fittings are
placed on or near seams and therefore require extra radiography as per API 650
5.7.3.4 11th Edition, extra costs will apply.
7. When tanks are coated we recommend the customer upgrade to stainless steel
couplings. Upgrade pricing is available upon request

Show Less

One (1) 1000 BBL single walled tank 15'-3" x 32'-0" high
•             1000 Bbl nominal capacity single wall, steel tank
•             12 Oz Maximum Pressure Design capable (See anchor chair options below, as some engineered versions may require anchoring and 1/4" first course to be 16 Oz rated)
•             Double pneumatic leak tested to 24 Oz
•             Floor thickness:1/4"
•             Shell and roof thickness: 3/16"
•             Minimum Design Temperature: -40 degrees F
•             Steel is G40.21-04 , 38W/44W, ASTM A36/ASME SA36-10/11, also meeting requirements of API 650 Group III                   
Additional Fittings included:
•             35' Caged Ladder (see note 1 below and price list for detail on OH&S Compliance options)
•             four (4) - lifting lugs
•             one (1) - tailing lug
•             Transportation stops (hauling pads)
•             Piping is not included with base tank. We will accommodate your internal or external piping as required, including custom internals.
Nozzle Description:
•             Three (3) - TBD" couplings for Level Gauge connections (two guide wire connections, one float wire connection, with coupling sizes automatically matched to gauge board model chosen in options below)
•             One (1) - 8" Standard thief hatch API connection (thief hatch options below) 
•             One (1) - 4" coupling on center roof (Can be up-sized if required, per attached pricelist)
•             One (1) - 24" x 36" API Standard manway c/w one-piece neoprene gasket (includes pre-delivery bolt-up)
•             All flanged nozzles to be A105N 150# RFSO with A-106B SCH 40 seamless pipe unless otherwise selected in options list)
•             All couplings to be A105N 3000# unless otherwise stated
•             Please see price list for per-nozzle pricing to customize tank

Show Less

One (1) 1000 BBL single walled tank 15'-3" X 32' high
•             1000 Bbl nominal capacity single wall, steel tank
•             12 Oz Maximum Pressure Design capable (See anchor chair options below, as some engineered versions may require anchoring and 1/4" first course to be 16 Oz rated)
•             Double pneumatic leak tested to 24 Oz
•             Floor thickness:1/4”
•             First Course: 1/4"
•             Remaining shell and roof thickness: 3/16”
•             Minimum Design Temperature: -40 degrees F
•             Steel is G40.21-04 , 38W/44W, ASTM A36/ASME SA36-10/11, also meeting requirements of API 650 Group III                   
Additional Fittings included:
•             35' Caged Ladder (see note 1 below and price list for detail on OH&S Compliance options)
•             four (4) – lifting lugs
•             one (1) – tailing lug
•             Transportation stops (hauling pads)
•             Piping is not included with base tank. We will accommodate your internal or external piping as required, including custom internals.
Nozzle Description:
•             Three (3) – TBD” couplings for Level Gauge connections (two guide wire connections, one float wire connection, with coupling sizes automatically matched to gauge board model chosen in options below)
•             One (1) - 8” Standard thief hatch API connection (thief hatch options below) 
•             One (1) - 4” coupling on center roof (Can be up-sized if required, per attached pricelist)
•             One (1) - 24” x 36” API Standard manway c/w one-piece neoprene gasket (includes pre-delivery bolt-up)
•             All flanged nozzles to be A105N 150# RFSO with A-106B SCH 40 seamless pipe unless otherwise selected in options list)
•             All couplings to be A105N 3000# unless otherwise stated
•             Please see price list for per-nozzle pricing to customize tank
GENERAL COMMENTS:
Technical Comments:
1. The above included ladder assembly may not comply with OH&S - Process Industry Practices standard STF05501 for fixed ladders and cages. Prices for an upgrade are available in options below. 
2. Roof to shell joint will be seal welded on the outside only as per API 650, Appendix F, and Detail B. For internally coated tanks, coating of the shell to roof joint must be grouted prior to coating and therefore grout will be used for repair of voids. (Note: This does not follow NACE RP-0178 figure A.7.) 
3. We made no provision for nozzle loading calculations and these are not included in the base tank price. 
4. A: We have not allowed for drafting changes beyond Revision 1. We therefore recommend you review initial markups thoroughly. Any further changes will be charged a rate of $90.00 per hour with a minimum charge of two hours per drawing affected. Changes made after IFC (Issued For Construction) stage may affect delivery.
4. B: We have not allowed for changes requiring engineering reviews. Changes will be charged a rate of $120.00 per hour with a minimum charge of two hours per drawing affected. Changes made after IFC stage may affect delivery. 
5. All standard accessories and appurtenances will be shipped loose unless otherwise stated. Installer is responsible for ensuring that all connections, including manway nuts and bolts are tightened and equipment is inspected prior to it being put into commission. 
6. Unless otherwise stated above, radiography is not included. If fittings are placed on or near seams and therefore require extra radiography per API 650 5.7.3.4 11th Edition, extra costs will apply. 
7. When tanks are coated, we recommend the customer upgrade to stainless steel couplings. Upgrade pricing is included in the price list below.

Show Less

One (1) 1000 BBL single walled tank 15'-3" x 32'-0" high
•             1000 Bbl nominal capacity single wall, steel tank
•             12 Oz Maximum Pressure Design capable (See anchor chair options below, as some engineered versions may require anchoring and 1/4" first course to be 16 Oz rated)
•             Double pneumatic leak tested to 24 Oz
•             Floor thickness:1/4"
•             Shell and roof thickness: 3/16"
•             Minimum Design Temperature: -40 degrees F
•             Steel is G40.21-04 , 38W/44W, ASTM A36/ASME SA36-10/11, also meeting requirements of API 650 Group III                   
Additional Fittings included:
•             35' Caged Ladder (see note 1 below and price list for detail on OH&S Compliance options)
•             four (4) - lifting lugs
•             one (1) - tailing lug
•             Transportation stops (hauling pads)
•             Piping is not included with base tank. We will accommodate your internal or external piping as required, including custom internals.
Nozzle Description:
•             Three (3) - TBD" couplings for Level Gauge connections (two guide wire connections, one float wire connection, with coupling sizes automatically matched to gauge board model chosen in options below)
•             One (1) - 8" Standard thief hatch API connection (thief hatch options below) 
•             One (1) - 4" coupling on center roof (Can be up-sized if required, per attached pricelist)
•             One (1) - 24" x 36" API Standard manway c/w one-piece neoprene gasket (includes pre-delivery bolt-up)
•             All flanged nozzles to be A105N 150# RFSO with A-106B SCH 40 seamless pipe unless otherwise selected in options list)
•             All couplings to be A105N 3000# unless otherwise stated
•             Please see price list for per-nozzle pricing to customize tank

Show Less

There are currently no details for this product.

Show Less

• Production tank• 15'3" OD x 32' HIGH• API 650 modified • Tank contains the following: 
Roof 3/16 A36
Shell 3/16 A36
Floor 1/4 A36
Built to API 650 Modified Specifications Tested to 24 oz

Nozzles• 4 x 3" RFSO• 4 x 4" RFSO DUAL FF• 1 x 4" RFSO with gooseneck and birdscreen (vent) (Can be up-sized if req'd)• 2 x 1/2" 150# half couplings (Gauge Board)• 1 x 1 1/2" 15# half coupling (Gauge Board)

Included:• ExternalSSPC SP14 blast and paint, black• Internally Blast (SSPC-Sp5) and Coat floor and 3' up shell walls with Enviroline 356 (Further coating can be accommodated at $ 12,500 adder)• Clay and Bailey Sour thief  hatch set at 4.0 pressure, 4 Oz Vacuum. (Thief hatch can be re-sprung to suit your requirements)• TGS Sour Service gauge board• 24" x 36" manway with split cover (c.w. 6" nozzle mounted on manway)• standard caged ladder• 4 x transportation pads• standard lift lugs

Notes
Tanks are FOB Carmangay, AB• Tanks are new - never put into service• Tanks formerly built for major oil company• 2 tanks in stock TK-61191-T, TK-61193-T

Show Less

One (1) 1000 BBL single walled tank 15'-3" x 32'-0" high
•             1000 Bbl nominal capacity single wall, steel tank
•             16 Oz Maximum Pressure Design capable (See anchor chair options below, as some engineered versions may require anchoring to be 16 Oz rated)
•             Double pneumatic leak tested to 24 Oz
•             Floor thickness:1/4"
•             Shell and roof thickness: 3/16"
•             Minimum Design Temperature: -40 degrees F
•             Steel is G40.21-04 , 38W/44W, ASTM A36/ASME SA36-10/11, also meeting requirements of API 650 Group III

Additional Fittings included:
•             35' Caged Ladder (see note 1 below and price list for detail on OH&S Compliance options)
•             four (4) - lifting lugs
•             one (1) - tailing lug
•             Transportation stops (hauling pads)
•             Piping is not included with base tank. We will accommodate your internal or external piping as required, including custom internals.

Nozzle Description:
•             Three (3) - TBD" couplings for Level Gauge connections (two guide wire connections, one float wire connection, with coupling sizes automatically matched to gauge board model chosen in options below)
•             One (1) - 8" Standard thief hatch API connection (thief hatch options below) 
•             One (1) - 4" coupling on center roof (Can be up-sized if required, per attached pricelist)
•             One (1) - 24" x 36" API Standard manway c/w one-piece neoprene gasket (includes pre-delivery bolt-up)
•             All flanged nozzles to be A105N 150# RFSO with A-106B SCH 40 seamless pipe unless otherwise selected in options list)
•             All couplings to be A105N 3000# unless otherwise stated
•             Please see price list for per-nozzle pricing to customize tank

GENERAL COMMENTS

1. The above included ladder assembly may not comply with OH&S - Process Industry Practices standard STF05501 for fixed ladders and cages. Prices for an upgrade are available in options below. 
2. Roof to shell joint will be seal welded on the outside only as per API 650, Appendix F, and Detail B. For internally coated tanks, coating of the shell to roof joint must be grouted prior to coating and therefore grout will be used for repair of voids. (Note: This does not follow NACE RP-0178 figure A.7.) 
3. We made no provision for nozzle loading calculations and these are not included in the base tank price. 
4. A: We have not allowed for drafting changes beyond Revision 1. We therefore recommend you review initial markups thoroughly. Any further changes will be charged a rate of $90.00 per hour with a minimum charge of two hours per drawing affected. Changes made after IFC (Issued For Construction) stage may affect delivery. 
4. B: We have not allowed for changes requiring engineering reviews. Changes will be charged a rate of $120.00 per hour with a minimum charge of two hours per drawing affected. Changes made after IFC stage may affect delivery. 
5. All standard accessories and appurtenances will be shipped loose unless otherwise stated. Installer is responsible for ensuring that all connections, including manway nuts and bolts are tightened and equipment is inspected prior to it being put into commission. 
6. Unless otherwise stated above, radiography is not included. If fittings are placed on or near seams and therefore require extra radiography per API 650 5.7.3.4 11th Edition, extra costs will apply. 
7. When tanks are coated, we recommend the customer upgrade to stainless steel couplings. Upgrade pricing is included in the price list below.

Show Less

There are currently no details for this product.

Show Less

10,000 BBl TANK (Nominal)
3 - Rings
Center Pole Supported Steel Cone Roof, Flat
Steel Floor
Designed Per API 12-B
47.2 PSF Deck Live Load
Factory Powder Coated throughout with 5 mil average dry film thickness:
     Dupont "Tank Tan," a Thermal Set Epoxy Powder Coating on Tank Interior and Underside of Floor
     3 mil average dry film thickness using Dupont "Superior Sand,"
     a Thermal Set TGIC Polyester Powder Coating on Tank Exterior
54'-11 3/4" Diameter x 24'-1 1/2" High Bolted Steel Storage Tanks
with the following appurtenances:
1 - 24" x 36" Flush Shell Manway
1 - 24" Diameter Shell Manway
1 - 8" Gauge Hatch
1 - Set of Tank Drawings


HARDWARE: 
Standard Galvanized Hardware Exterior, Encapsulated Hardware Interior and BUNA N gasket used throughout.


Options available, and priced separately:
• 6" High x 57' Diameter, 12 Gauge Galvanized Grade Band $1,750.00/each
• 12" High x 57' Diameter, 12 Gauge Galvanized Grade Band $3,400.00/each
• 24' Galvanized Stairway $11,000.00
• Nozzles: use $56.00 per diameter inch
• 3M "Scotchkote 134" Adder $17,200.00
• Galvanized Exterior Ladder W/ (2) 5' Wide Rails $1,700.00


Not included:
Installation (Typical warm weather tank only erection time is 70 man-days, add approx. 25 more days for colder weather setup)
freight
unloading
drayage
freight forwarder
secondary containment
containers
signage
grout
insulation
foundation (concrete or gravel)
Level indicator
gooseneck vent
anchor bolt assemblies
fiber expansion board
Level switches/alarms
process piping
probes
internals such as downcomers, risers, skimmers etc.
freeze protection
valves
instrumentation
float valves or switches
flex tends
meters
grading
gauges
electrical contracting
surveying

Show Less

There are currently no details for this product.

Show Less

There are currently no details for this product.

Show Less

One (1) 1500 BBL single walled tank 21'-6" x 24'-0" high
•             1500 Bbl nominal capacity single wall, steel tank
•             12 Oz Maximum Pressure Design capable (See anchor chair options below, as some engineered versions may require anchoring and 1/4" first course to be 16 Oz rated)
•             Double pneumatic leak tested to 20 Oz
•             Floor thickness:1/4"
•             First course (8')  thickness:1/4"
•             Roof thickness:1/4"
•             Remaining Shell thickness: 3/16"
•             Minimum Design Temperature: -40 degrees F
•             Steel is G40.21-04 , 38W/44W, ASTM A36/ASME SA36-10/11, also meeting requirements of API 650 Group III                   
Additional Fittings included:
•             43' Caged Ladder (see note 1 below and price list for detail on OH&S Compliance options)
•             four (4) - lifting lugs
•             one (1) - tailing lug
•             Transportation stops (hauling pads)
•             Piping is not included with base tank. We will accommodate your internal or external piping as required, including custom internals.
Nozzle Description:
•             Three (3) - TBD" couplings for Level Gauge connections (two guide wire connections, one float wire connection, with coupling sizes automatically matched to gauge board model chosen in options below)
•             One (1) - 8" Standard thief hatch API connection (thief hatch options below) 
•             One (1) - 4" coupling on center roof (Can be up-sized if required, per attached pricelist)
•             One (1) - 24" x 36" API Standard manway c/w one-piece neoprene gasket (includes pre-delivery bolt-up)
•             All flanged nozzles to be A105N 150# RFSO with A-106B SCH 40 seamless pipe unless otherwise selected in options list)
•             All couplings to be A105N 3000# unless otherwise stated
•             Please see price list for per-nozzle pricing to customize tank

Show Less

One (1) 200 BBL double walled tank 
External tank: 12' dia. x 10' high
Internal tank 11'-9" x 10'-0" high
•             190 Bbl nominal capacity double wall, steel tank, 1.5" between shell walls
•             12 Oz Maximum Pressure Design capable (See anchor chair options below, as some engineered versions may require anchoring to be 16 Oz rated)
•             Double pneumatic leak tested to 24 Oz
•             Floor thickness:1/4"
•             Shells and roof thickness: 3/16"
•             Minimum Design Temperature: -40 degrees F
•             Steel is G40.21-04 , 38W/44W, ASTM A36/ASME SA36-10/11, also meeting requirements of API 650 Group III                   
Additional Fittings included:
•             10' Caged Ladder O, H&S compliant
•             two (2) - lifting lugs
•             Piping is not included with base tank. We will accommodate your internal or external piping as required, including custom internals.
Nozzle Description:
•             Three (3) - TBD" couplings for Level Gauge connections (two guide wire connections, one float wire connection, with coupling sizes automatically matched to gauge board model chosen in options below)
•             One (1) - 8" Standard thief hatch API connection (thief hatch options below) 
•             One (1) - 4" coupling on center roof (Can be up-sized if required, per attached pricelist)
•             One (1) - 24" x 36" API Standard manway c/w one-piece neoprene gasket (includes pre-delivery bolt-up)
•             All flanged nozzles to be A105N 150# RFSO with A-106B SCH 40 seamless pipe unless otherwise selected in options list)
•             All couplings to be A105N 3000# unless otherwise stated
•             Please see price list for per-nozzle pricing to customize tank

Show Less

12'OD (11' 9" ID) x 10'H 
• 190bbl (30.2 m3) nominal capacity
• 6" WF skid
• 2 - lifting lugs
• Ladder w/ top loop
• Built to API 12F specs
• Steel is G40.21-04 , 38W/44W, ASTM A36/ASME SA36-10/11, also meeting requirements of API 650 Group 3
• 1/4" floor
• 3/16" shell and roof


Nozzle Description:
• All nozzles A105N 150# with A-106B seamless pipe
• 3" 150# nozzle for HLSD
• 2- 2" 150# nozzles
• 4" 3000# coupling for drain
• 3 - 3/4" couplings for Level gauge connection
• 4" Vent 
• 8" thief hatch connection
• 24"x 36" std Man way 

Show Less

One 2000bbl API 650 MODIFIED tanks including the following:
General:
21'6"D x 32'H
• 2000 Bbl nominal capacity
• Single wall, steel tank
• 8 Oz. design, must choose either base skid or anchor chair option below to make 16 Oz design
• 35' Caged ladder w/ side platform at 29' elevation
• 4- hauling pads
• 4 - lifting lugs
• 1 - tailing lug
• 1- grounding lug
• 3" channel compression ring
• Steel is G40.21-13, 38W/44W, ASTM A36/ASME SA36-10/11, also compliant with requirements of API 650 Group 3
• 1/4" floor, 1st course, and roof
• 3/16" top 3 courses of shell
• 1/4" plate dividing wall reinforced w/ structural steel
Testing:
• Double pneumatic air/soap leak test to 20 Oz.
Nozzle Description:
• All nozzles A105N 150# with A-106B sch 40 seamless pipe
• three -couplings for Level gauge connection
• one 8" thief hatch connection
• two- 24x36 split manways w/ 1- piece neoprene gaskets and Grade 5 bolt up

Options (per tank)
• Engineered base skid welded to tank bottom 
Please inquire
• 8 anchor chairs
Please inquire

Price includes initial CAD drawing and 2 revisions. 
Any additional revisions and drafting will be charged on an hourly basis.

Show Less

One (1) 2000 BBL single walled tank 21'-6" x 32'-0" high
•             2000 Bbl nominal capacity single wall, steel tank
•             12 Oz Maximum Pressure Design capable (See anchor chair options below, 
               as some engineered versions may require anchoring and 1/4" first course to be 16 Oz rated)
•             Double pneumatic leak tested to 24 Oz
•             Floor thickness:1/4"
•             First course (8')  thickness:1/4"
•             Roof thickness:1/4"
•             Remaining Shell  thickness: 3/16"
•             Minimum Design Temperature: -40 degrees F
•             Steel is G40.21-04 , 38W/44W, ASTM A36/ASME SA36-10/11, also meeting requirements of API 650 Group III                   
Additional Fittings included:
•             35' Caged Ladder (see note 1 below and price list for detail on OH&S Compliance options)
•             four (4) - lifting lugs
•             one (1) - tailing lug
•             Transportation stops (hauling pads)
•             Piping is not included with base tank. 
              We will accommodate your internal or external piping as required, including custom internals.
Nozzle Description:
•             Three (3) - TBD" couplings for Level Gauge connections 
              (two guide wire connections, one float wire connection, 
              with coupling sizes automatically matched to gauge board model chosen in options below)
•             One (1) - 8" Standard thief hatch API connection (thief hatch options below) 
•             One (1) - 4" coupling on center roof (Can be up-sized if required, per attached pricelist)
•             One (1) - 24" x 36" API Standard manway c/w one-piece neoprene gasket (includes pre-delivery bolt-up)
•             All flanged nozzles to be A105N 150# RFSO with A-106B SCH 40 seamless pipe unless otherwise selected in options list)
•             All couplings to be A105N 3000# unless otherwise stated
•             Please see price list for per-nozzle pricing to customize tank

Show Less

RE: 1-1000BBL single containment tank  15'3” x 32’ high
Tank contains the following:
Roof 1/4” A36
Shell 1/4” A36 (first course_
Shell 3/16” A36 (remaining three courses)
Floor 1/4” A36
Built to API 650 Modified Specifications
16 ounce non-engineered design - Tested to 24 oz
Radiography at cost plus 20%
Material – API 650 Group IIIA normalized
G40.21-04 , 38W/44W, ASTM
A36/ASME SA36-10/11
MDMT -40 degrees F

NOTE:
This material has been manufactured , tested and found to meet the specifications and purchase order requirements regarding structural quality coil for conversion to:
 * CSA G40.21-04 Grade 38W/44W
 * ASTM A36
 *ASME SA36-10-11 ADD
These designations meet all the material requirements of API650 (12th Edition) Group III - Killed Fine Grain Practice

15'3” dia x 32’ tall built to API 650 MODIFIED
Thief hatch flange (thief hatch options below)
Gauge board fittings and brackets (gauge board options below)
nozzles as adders (see below)
no piping included
3” threaded near ladder for HLSD
4” center roof vent c/w 180 and bird screen
24” x 48” sidewall manway
Caged Ladder (OH&S)
4 lift lugs
1 tailing lug
4 hauling pads
grounding lug

As per attached drawing OilPro Stock 1000BBL REV C
Final price to be confirmed on appoved drawings

GENERAL COMMENTS
1. The above quoted ladder assembly has been engineered to comply with OH & S -
Process Industry Practices standard STF05501 for fixed ladders and cages.
Please Note:
•30 feet is the limit for a single ladder with cage only.
•Two options for taller ladder are:
-Multiple offset ladder sections with landings at the transition points.
-Single ladder with fall arrest system (note cage is also not required if fall arrest
system is used)
2. Roof to shell joint will be seal welded on the outside only as per API 650,
Appendix F, and Detail B. For internally coated tanks, coating of the shell to roof
joint must be grouted prior to coating and therefore grout will be used for repair of voids. (Note: This does not follow NACE RP-0178 figure A.7.)
3. We have made no provision for nozzle loading calculations.
4. We have not allowed for any engineering or drafting changes. Any changes will be
charged a rate of $90.00 per hour for drafting and $120.00 per hour for engineering
with a minimum charge of two hours per drawing affected. This will also affect the
above quoted delivery.
5. All standard accessories and appurtenances will be shipped loose unless
otherwise stated. Customer is responsible for ensuring that all connections,
including manway nuts and bolts are tightened and equipment is inspected prior to it
being put into commission.
6. Unless otherwise stated above radiography has not been included. If fittings are
placed on or near seams and therefore require extra radiography as per API 650
5.7.3.4 11th Edition, extra costs will apply.
7. When tanks are coated we recommend the customer upgrade to stainless steel
couplings. Upgrade pricing is available upon request

Show Less

One (1) 2000 BBL single walled tank 21'-6" x 32'-0" high
•             2000 Bbl nominal capacity single wall, steel tank
•             12 Oz Maximum Pressure Design capable (See anchor chair options below, 
               as some engineered versions may require anchoring and 1/4" first course to be 16 Oz rated)
•             Double pneumatic leak tested to 24 Oz
•             Floor thickness:1/4"
•             First course (8')  thickness:1/4"
•             Roof thickness:1/4"
•             Remaining Shell  thickness: 3/16"
•             Minimum Design Temperature: -40 degrees F
•             Steel is G40.21-04 , 38W/44W, ASTM A36/ASME SA36-10/11, also meeting requirements of API 650 Group III                   
Additional Fittings included:
•             35' Caged Ladder (see note 1 below and price list for detail on OH&S Compliance options)
•             four (4) - lifting lugs
•             one (1) - tailing lug
•             Transportation stops (hauling pads)
•             Piping is not included with base tank. 
              We will accommodate your internal or external piping as required, including custom internals.
Nozzle Description:
•             Three (3) - TBD" couplings for Level Gauge connections 
              (two guide wire connections, one float wire connection, 
              with coupling sizes automatically matched to gauge board model chosen in options below)
•             One (1) - 8" Standard thief hatch API connection (thief hatch options below) 
•             One (1) - 4" coupling on center roof (Can be up-sized if required, per attached pricelist)
•             One (1) - 24" x 36" API Standard manway c/w one-piece neoprene gasket (includes pre-delivery bolt-up)
•             All flanged nozzles to be A105N 150# RFSO with A-106B SCH 40 seamless pipe unless otherwise selected in options list)
•             All couplings to be A105N 3000# unless otherwise stated
•             Please see price list for per-nozzle pricing to customize tank

Show Less

There are currently no details for this product.

Show Less

There are currently no details for this product.

Show Less

There are currently no details for this product.

Show Less

New, surplus tank shell
2,250 Bbl capacity
23'-6" wide x 32' high
Cone Bottom design.
Drawing available but as unit is not complete it can be modified to suit.

Show Less

Surplus 25 Bbl (4.4m3) Nominal Capacity tank
Built by Corlac Industries, Nisku, AB
Wo. No. 4552-06
Built June, 2000
Design:1512 mm high x 1922 mm dia.


Design features:
- 6.4 mm floor
- 4.8 mm shell
- 4.8 mm roof
Design Pressure: 1.7 kPa
Design Vacuum: 1.7 kPa
Shell, deck and floor material: A-36


2 x lift lugs on tanks
Tank is mounted on I-beam skid
external insulation with Urethane Foam, approx. 1.5" (Needs new elastomeric coat applied.
Thief hatch, mounted on top manway
To hinged manway cover
Lean-to building c.w
- 36" x 36" window c.w. slider, bug screen
- door c.w. panic hardware


Packaging:
- Bromley Fuel Gas scrubber c.w. 
  level switch
  Pressure Gauge
  PSV
  drain
- 3 pen recorder
Barton 202 c.w. 5 valve manifold
- meter run 2" Sr., flanged.
- Catalytic header c.w. hood and vent.


OilPro will consider sale of unit as a whole or just as a tank.

Show Less

RE: 1-1000BBL single containment tank  15'3" x 32' high
Tank contains the following:
Roof 1/4" A36
Shell 1/4" A36 (first course_
Shell 3/16" A36 (remaining three courses)
Floor 1/4" A36
Built to API 650 Modified Specifications
16 ounce non-engineered design - Tested to 24 oz
Radiography at cost plus 20%
Material - API 650 Group IIIA normalized
G40.21-04 , 38W/44W, ASTM
A36/ASME SA36-10/11
MDMT -40 degrees F

NOTE:
This material has been manufactured , tested and found to meet the specifications and purchase order requirements regarding structural quality coil for conversion to:
 * CSA G40.21-04 Grade 38W/44W
 * ASTM A36
 *ASME SA36-10-11 ADD
These designations meet all the material requirements of API650 (12th Edition) Group III - Killed Fine Grain Practice

15'3" dia x 32' tall built to API 650 MODIFIED
Thief hatch flange (thief hatch options below)
Gauge board fittings and brackets (gauge board options below)
nozzles as adders (see below)
no piping included
3" threaded near ladder for HLSD
4" center roof vent c/w 180 and bird screen
24" x 48" sidewall manway
Caged Ladder (OH&S)
4 lift lugs
1 tailing lug
4 hauling pads
grounding lug

As per attached drawing OilPro Stock 1000BBL REV C
Final price to be confirmed on appoved drawings

GENERAL COMMENTS
1. The above quoted ladder assembly has been engineered to comply with OH & S -
Process Industry Practices standard STF05501 for fixed ladders and cages.
Please Note:
• 30 feet is the limit for a single ladder with cage only.
• Two options for taller ladder are:
-Multiple offset ladder sections with landings at the transition points.
-Single ladder with fall arrest system (note cage is also not required if fall arrest
system is used)
2. Roof to shell joint will be seal welded on the outside only as per API 650,
Appendix F, and Detail B. For internally coated tanks, coating of the shell to roof
joint must be grouted prior to coating and therefore grout will be used for repair of voids. (Note: This does not follow NACE RP-0178 figure A.7.)
3. We have made no provision for nozzle loading calculations.
4. We have not allowed for any engineering or drafting changes. Any changes will be
charged a rate of $90.00 per hour for drafting and $120.00 per hour for engineering
with a minimum charge of two hours per drawing affected. This will also affect the
above quoted delivery.
5. All standard accessories and appurtenances will be shipped loose unless
otherwise stated. Customer is responsible for ensuring that all connections,
including manway nuts and bolts are tightened and equipment is inspected prior to it
being put into commission.
6. Unless otherwise stated above radiography has not been included. If fittings are
placed on or near seams and therefore require extra radiography as per API 650
5.7.3.4 11th Edition, extra costs will apply.
7. When tanks are coated we recommend the customer upgrade to stainless steel
couplings. Upgrade pricing is available upon request

Show Less

23'-6"D x 40'H
• 3000 bbl nominal capacity
• Single wall, steel tank
• 40' Caged ladder (OH&S approved hoops) 
        since ladder is over 30' see below options to make OH&S compliant.
• Transportation stops
• 4 - lifting lugs
• 1 - tailing lug
• 3" channel compression ring
• Steel is G40.21-13 , 38W/44W, ASTM A36/ASME SA36-10/11
• 1/4" floor, 1st course (8'), and roof
• 3/16" top 4 courses of shell(32')
• Double pneumatic air/soap leak test to 20 Oz.


Nozzle Description:
• All nozzles A105N 150# RFSO flanges with A-106 B SCH 40 seamless pipe
• All couplings A105N 3000#
• 3 - couplings for level gauge connection
• 8" thief hatch connection
• 24"x 36" std manway 


Options (per tank)
• Since ladder is over 30' in height, OH&S requires a break platform
  or fall arrest system. See below for 2 upgrade options (base ladder already included in quote)
1. Upgrade to split ladder w/ break platform

2. 8- Anchor chairs required to make tank 16oz design

Show Less

One (1) 3000 BBL single walled tank 23'-6" x 40'-0" high
•              3000 Bbl nominal capacity single wall, steel tank
•              16 Oz Maximum Pressure Design capable (See anchor chair options below, as some engineered versions may require anchoring to be 16 Oz rated)
•              Double pneumatic leak tested to 20 Oz
•              Floor thickness:1/4"
•              First course (8')  thickness:1/4"
•              Roof thickness:1/4"
•              Remaining Shell thickness: 3/16"
•              Minimum Design Temperature: -40 degrees F
•              Steel is G40.21-04 , 38W/44W, ASTM A36/ASME SA36-10/11, also meeting requirements of API 650 Group III                   
Additional Fittings included:
•              43' Caged Ladder (see note 1 below and price list for detail on OH&S Compliance options)
•              four (4) - lifting lugs
•              one (1) - tailing lug
•              Transportation stops (hauling pads)
•              Piping is not included with base tank. We will accommodate your internal or external piping as required, including custom internals.
Nozzle Description:
•              Three (3) - TBD" couplings for Level Gauge connections (two guide wire connections, one float wire connection, with coupling sizes automatically matched to gauge board model chosen in options below)
•              One (1) - 8" Standard thief hatch API connection (thief hatch options below) 
•              One (1) - 4" coupling on center roof (Can be up-sized if required, per attached pricelist)
•              One (1) - 24" x 36" API Standard manway c/w one-piece neoprene gasket (includes pre-delivery bolt-up)
•              All flanged nozzles to be A105N 150# RFSO with A-106B SCH 40 seamless pipe unless otherwise selected in options list)
•              All couplings to be A105N 3000# unless otherwise stated
•              Please see price list for per-nozzle pricing to customize tank

Show Less

There are currently no details for this product.

Show Less

There are currently no details for this product.

Show Less

There are currently no details for this product.

Show Less

1- 30 bbl API 12F tank including the following,

General:
Dia 6ft D x 6ft H
- 30bbl (4.7 m3) nominal capacity
- Single wall, steel tank
- Design Pressure 2/-.25 KPA
- Design Temperature -29%u00B0C/120%u00B0C
- Corrosion Allowance: 3.2 mm
- 2 - lifting lugs (rated for -45%u00B0C)
- 1 - tailing lug (rated for -45%u00B0C)
- Steel is G40.21-13, 38W/44W, ASTM A36/ASME SA36-10/11
- 3/8" floor
- 5/16" shell and roof
- Ladder w/ 3'x5' roof platform w/ safety gate & guard rails

Nozzle Description:
• All nozzles A105N 150# RFWN flanges with A-106B sch 40 seamless pipe
• All couplings A105N 3000#

Mark Size Qty Flange Rating Face Service
N1 6in 1 150# Vacuum residue Inlet
N2 8in 1 150# Chemical K2CO3 Inlet
N3 6in 1 150# Blended Vac Res Outlet c-w vortex breaker
N4 8in 1 150# Mixer Connector
N5 1in 1 150# Vent c-w Goose neck & Bird screen
N6 2in 1 150# Drain c-w Internal Siphon
N7 2in 1 300# Temperature Transmitter
N8 6in 1 300# Level Transmitter (radar Type)
N9 8in 1 150# Spare c-w Blind
N10 8in 1 150# Heater coil connnection
N11 1in 1 150# Steam out

M1B 24in 1 API 650 Fab'd Shell Manway c-w Handle

N5 is flange only , gooseneck vent by others (or need dimensions of height required for quoting)

Options (per tank)

- MPI by 3rd party on lifting Lugs $ 285.00
- Hydro-Test (fill with water ) $ 675.00

Testing:
• As per API 12F- Double pneumatic leak test to 16 oz
• See below options for additional testing


All prices subject to GST:

- Price includes initial Solidworks CAD drawing and 2 revisions.
- Any additional revisions and drafting will be charged at $90/hour.
- This tank would have an estimated bare steel delivery date to Cannon Coatings 3 weeks starting after
confirmation of order,
options, receipt of deposit, approved IFC drawings, and shop availability. (1st come basis, delivery could change)

*NOTE: Firm completion date will be given after the above items are taken care of.

Terms - TBC

Show Less

There are currently no details for this product.

Show Less

1- 3850 Bbl API 650 MODIFIED tanks including the following,
General:
23'6" D x 50'H
• 3850 Bbl nominal capacity
• Single wall, steel tank
• 32 oz pressure / 0.4 oz design vacuum 
         - must choose either base skid or anchor chairs below
• 4- hauling pads
• 4 - lifting lugs
• 1 - tailing lug
• 1- grounding lug
• 6" channel compression ring
• Steel is G40.21-13, 38W/44W, ASTM A36/ASME SA36-10/11, also meeting requirements of API 650 Group 3
• 5/16" floor, 1st course (8')
• 1/4" 2nd & 3rd course (16')
• 3/16" top courses of shell
• 3/8" roof


Testing:
• Double pneumatic air/soap leak test to 8 Oz.
        - other testing options available also


Nozzle Description:
• All nozzles A105N 150# with A-106B sch 40 seamless pipe
• 3 - couplings for Level gauge connection
• 4- 6" nozzles
• 8" thief hatch connection
• 24"x 36" oval manway w/ ½" thick cover. C/W 1-piece neoprene gasket and grade 5 bolt-up

Show Less

400-Tank 
RE: 1-400BBL single containment tank 12' x 20' high
Tank contains the following:
Roof 3/16 A36
Shell 3/16 A36
Floor %u00BC A36
Built to API 12F Modified Specifications
16 ounce non-engineered design - Tested to 24 oz
Steel is G40.21-04, 38W/44W, ASTM A36/ASME SA36-10/11
Material - API 650 Group IIIA normalized
G40.21-04 , 38W/44W, ASTM
A36/ASME SA36-10/11
MDMT -40 degrees F


12'dia x 20' tall built to API 12F MODIFIED
Materials:
Floor 1/4"
Roof and Walls 3/16"A
All Shell Material A36
API 650 Group IIIA Normalized.


API 12F modified design
MDMT -40 F, 
16 Oz design tested to 24 Oz 
Standard L Skid.


Incl:
Thief hatch flange
3" 3000# 1/2 coupling for HLSD
gaugeboard fittings and brackets
4" center roof vent with goose neck and bird screen
24" x 36" sidewall manway
Caged Ladder (OH&S)2 Lift lugs
1 - tailing lug. 


See adders for nozzles, paint and coating


GENERAL COMMENTS
1. The above quoted ladder assembly has been engineered to comply with OH & S Process Industry Practices standard STF05501 for fixed ladders and cages.
Please Note:
• 30 feet is the limit for a single ladder with cage only.
• Two options for taller ladder are:
-Multiple offset ladder sections with landings at the transition points.
-Single ladder with fall arrest system (note cage is also not required if fall arrest system is used)
2. Roof to shell joint will be seal welded on the outside only as per API 650, Appendix F, and Detail B. For internally coated tanks, coating of the shell to roof joint must be grouted prior to coating and therefore grout will be used for repair of
voids. (Note: This does not follow NACE RP-0178 figure A.7.)
3. We have made no provision for nozzle loading calculations.
4. We have not allowed for any engineering or drafting changes. Any changes will be charged a rate of $90.00 per hour for drafting and $120.00 per hour for engineering with a minimum charge of two hours per drawing affected. This will also affect the
above quoted delivery.
5. All standard accessories and appurtenances will be shipped loose unless otherwise stated. Customer is responsible for ensuring that all connections,
including manway nuts and bolts are tightened and equipment is inspected prior to it being put into commission.
6. Unless otherwise stated above radiography has not been included. If fittings are placed on or near seams and therefore require extra radiography as per API 650
5.7.3.4 11th Edition, extra costs will apply.
7. When tanks are coated we recommend the customer upgrade to stainless steel couplings. Upgrade pricing is available upon request

Show Less

TANK DESCRIPTION
Item 1 - 400 BBL Heated Single Wall Tank 
- 400 BBL (64 m3) nominal capacity 
- 12'-0" (3.66 m) diameter x 20'-0" (6.10 m) high 
- 3/16" (4.76 mm) shell plate 
- 3/16" (4.76 mm) roof plate 
- 1/4" (6.35 mm) floor plate 
- 0/0" (0.00 mm) corrosion allowance 


Nozzles: 
N1 1
4" 150# RFSO N N OUTLET 
N2 1
4" 150# RFSO N N OUTLET 
N3 1
4" 150# RFSO N N INLET 
N4 1
3" 150# RFSO N Y TRUCK OUT (IN VAULT) 
N5 1
3" 150# RFSO Y N INLET (IN VAULT) 
C1 1
3/4" 3000# CPLG N N GAUGEBOARD 
C2 1
3" 3000# CPLG N N LSHH 
C3 1
4" 3000# CPLG N N VENT C/W PLUG 
C4 1
4" 3000# CPLG N N DRAIN C/W PLUG 


Accessories and Appurtenances: 
- One (1) standard 2' x 3' shell manway c/w cover, gasket, bolts and nuts 
- One (1) standard open pulley gauge board assembly c/w non-guided float, 1/8" steel aircraft cable, board marked in cubic meter increments and all hardware required for complete assembly 
- One (1) 8" diameter Jayco sweet service thief hatch set at 4 oz. pressure and .4 oz. vacuum 
- One (1) standard ladder c/w top hoop 
- Two (2) standard lifting lugs 
- One (1) safety harness lug 
- One (1) standard L-Skid two saddle design 
- One (1) 3' x 5' Envirovault c/w 12" x 24" 8000 BTU CataDyne heater & wiring package 


Internal Finish: 
Floor 
Blast: nil 
Finish: nil 
Roof 
Blast: nil 
Finish: nil 
Shell 
Blast: nil 
Finish: nil 
External Finish: 
Floor 
Blast: nil 
Finish: nil 
Insulation: nil 
Shell and Roof 
Blast: nil 
Finish: nil 
Insulation: Apply 1-1/2" spray on urethane foam insulation c/w one coat of black elastomeric sealant
Notes


TANK SPECIFICATIONS 
Fabrication 
Tanks will be built to industry standards using API-650 code as reference only. Labeling shall be manufacturer's. No other specifications shall apply. 
Design Pressure: 16 Oz. pressure / 0.4 Oz vacuum 
Design Temperature: -130 deg C to 93 deg C 
Testing 
Air test to 1.5 times the design pressure 
Material 
Plate: CSA G40.21M-300W (CSA G40.21-44W) plate or equivalent 
Structural: A-36 or A-53-B ERW pipe 
Fittings: screwed, A-105, 3000# F.S. 
welded, A-234-WPB 
Flanges: A-105, 150# RFSO 
Pipe: Nozzles, A-106-B pipe 
Internals, A-53-B ERW pipe 
Mechanical Guarantee 
We warrant parts and labour against defects in material and workmanship for a period of eighteen months from date of manufacture, but not to exceed one (1) year from date of commissioning.

Show Less

400 bbl API 12F tank, constructed as follows:
General:
12’D x 20’H
• Sweet or Sour service
• 400 bbl (64 m3) nominal capacity
• Single wall, steel tank
• 8” WF L-skid
• 2– lifting lugs
• Ladder w/ top loop
• Built to API 12F specs
• Steel is G40.21-04 , 38W/44W, ASTM A36/ASME SA36-10/11, also meeting requirements of API 650 Group 3
• ¼” floor
• 3/16” shell and roof


Nozzle Description:
• All nozzles A105N 150# with A-106B seamless pipe
• 4 x 4”  RFSO nozzle
• 2 x 4”  3000#Half coupling
• 4 x 3”  3000#Half coupling
• 3 x 2”  3000#Half coupling
• 8” thief hatch connection
•3" Down comer
•24”x 36” std Man way
12' dia. x 20’ tall built to API 12F MODIFIED


Materials:
Floor 1/4”
Roof and Walls 3/16"A
All Shell Material A36
API 650 Group IIIA Normalized.
API 12F modified design
MDMT -40 F,
16 Oz design tested to 24 Oz
Standard L Skid.

Show Less

1.0 General Description
400 Bbl single wall rental style flat bottom, uncoated tank.


2.0 TANK
2.1 GENERAL DESCRIPTION
• 12’OD x 20’ S/S A-36
• Single wall API12F modified
• Design Pressure: 8 oz pressure/0.5 oz vacuum
• -29/93°C
• 0” C.A.
• 3/16” Nom. Roof,
• 1/4” Nom. Floor
• 3/16” Nom. Base Course
• 3/16” Nom. Remaining Courses


2.2 TANK CONNECTIONS
M1 One (1) 2’ X 3’Sidewall Manway
N1 One (1) 4” 150# RFSO Flange
N2 One (1) 4” 150# RFSO Flange
N3 One (1) 4” 150# RFSO Flange
N4 One (1) 4” 150# RFSO Flange
N7 One (1) 4” Center Roof Coupling cw Gooseneck & Birdscreen
N8 One (1) 4” Drain Coupling
TH Thief Hatch One (1) 8” API Shop Fab. Flange


2.3 TANK APPURTENANCES
Ladder One (1) Ladder with Hoop at top
Hauling Pads not included
Gauge Board Clips Two (2)
Lifting Lugs Two (2)
Tailing Lugs not included
Ground Lug not included
Safety Tie off Lug One (1)
Name Plate One (1)


3.0 STRUCTURAL SKID / BUILDING
SKID [email protected] -2 Saddle Skid


4.0 ACCESSORIES & EQUIPMENT
Tag # Quantity Description
LG-100 One (1) Level Gauge
Tom cat (sweet) non guided float, pulley and gauge board
Thief Hatch One (1) Jayco JT-8
8 oz/0.4 sweet service


5.0 MECHANICAL / PIPING / FITTINGS
Threaded Fittings
Pipe: SA-106-B (Sch 40)
Threaded Fittings: SA-105, 3000#
Welded Components
Shells, Roof and Floor: A-36
Pipe: SA-106-B (Sch 40)
Flanges: SA-105N
Weld Fittings: SA-234-WPB
Threadolets and Couplings: SA-105N
Structural Attachments: 44W/A-36
Gaskets (ANSI): 1/8-inch, 316 S.S. Flex.
Gaskets (API): Buna Nitrile
Bolting: SA-193-B7, SA-194-2H
Internal Piping: none included
Internal Supports: none included
Internal Bolt up: none included
Skid: [email protected] -2 Saddle Skid


6.0 TESTING
Air-Testing: Tank will be air-tested to 1.5 times design (12oz).
Radiography: None Included
PWHT: None Included
Ultrasonic Test: None Included
Production Impact Test: None Included
Magnetic Particle Test: None Included
Dye Penetrant Test: None Included
Weld Hardness Test: None Included


7.0 PAINTING & COATING
EXTERNAL:
Surface Preparation: Commercial Brush Blast
Tank Finish: AUE 370
Insulation (Roof and Shell): None Included
Ladder and Platforms: AUE 370
Skid/Piping Finish: AUE 370
INTERNAL:
Surface Preparation: None Included
Tank Finish (Full): None Included


8.0 OPTIONS, PRICING AVAILABLE ON REQUEST
A. To add Internal Coating (Floor and 3’)
B. To upgrade to Caged Ladder
C. To provide Anode

Show Less

There are currently no details for this product.

Show Less

There are currently no details for this product.

Show Less

1- 50 BBL double wall tank 8’ dia x 8’-8" high
Used, surplus, reconditioned
externally insulated and clad.
Built in 2001 by Tornado
No Nameplate


Tank Includes:
N1- 2" 150 ANSI - drain
N2 - 4" cplg
Double wall
- Gauge Board connection
2- manways on roof, provide only access.
1- 8” Thief hatch nozzle c/w 8 oz thief hatch
1- plain ladder equal length mounting brackets
1- Gauge Board: painted on tank readout in m3
2- Lifting lugs


•3/16” shell, floor and roof
•Structural bottom skid c.w. pull bars and ears for slings
  10'-7" long 6" I-beam c.w. lifting lugs, checker plate floor


Tank is painted tan, and includes:
- Sweet thief hatch
- Sweet service gauge board, no indicator. c.w. snow guard. Open to atmosphere.


Partial horizontal Catalytic heater Foam Panel enclosure c.w. door c.w.
- Low Vent
- vent, high, adustable on vertical portion
- Catadyne heater, aimed at tank wall for heating process fluid c.w. thermostat, vent, regulator, approx. 12,000 BTU. 12" x 24" c.w. start cables.


Tank to be brought to reconditioned status in 3-5 working days a.r.a.d. and c.w. 1 year OilPro warranty.
No original drawings available, but nozzle orientation available.
As unit is used surplus, we recommend customer views tank prior to order to allow us to incorporate any changes requested at minimal cost if any.

Show Less

There are currently no details for this product.

Show Less

Superior 5000 Barrel Bolted Tank
5,000 BBLs (Nominal)
3 - Rings
Center Pole Supported Steel Cone Roof
Flat Steel
Floor, Designed per API 12-B
Factory Powder Coated internally and externally
38'-7 5/8" Diameter x 24'-1 1/2" High
Bolted Steel Storage Tanks complete with:

1 - 24" x 36" Flush Shell Manway c.w.2pcs Door
1 - 8" Thief Hatch
2 - 10" 150# Flanged Shell Nozzles
2 - 3.5' High X 5' Wide, Galvanized "Wing" Handrails
1 - Superior Model #2400, Liquid Level Indicator
1 - Set of Calculations & Tank Drawings
1 - 6" High x 12 Gauge Galvanized Grade Band for foundation

Show Less

5000 BARREL BOLTED TANK
5,000 BBLs (Nominal)
38’-7 5/8” Diameter x 24’-1 1/2” High
3 – Rings
1 in 12 pitched roof
Center Pole Supported Steel Cone Roof
Flat Steel Floor
Designed per API 12-B
15 PSF Roof Live Load
100 MPH Windload
Factory Powder Coated, 
throughout with 5 mil average dry film thickness using DuPont -Tank Tan,” 
a Thermal Set Epoxy Powder Coating on Tank Interior and Underside of Floor & 
3 mil average dry film thickness using DuPont -Sand,” 
a Thermal Set TGIC Polyester Powder Coating on Tank Exterior


Bolted Steel Storage Tanks complete with:
1 – 24” x 36” Flush Shell Manway c.w.2 pcs Door
1 – 20” Cone Deck Manway
1 – 8” Gauge Hatch
4 – 6” 150# Flanged Shell Nozzles
1 – Set of Calculations & Tank Drawings
1 – Galvanized Exterior Ladder W/ Blackguard
2 – 3.5’ High x 5’ Wide, Galvanized -Wing” Handrails
1 – Superior Model # 2400, Liquid Level Indicator W/ Oil Seal


HARDWARE: 
Standard Galvanized Hardware Exterior
Encapsulated Hardware Interior and Buna N gasket used throughout.


Options:
1. To Coat the interior of the above referenced bolted tank with 7-10 mils of 3M Scotchkote 134.


2. To design the above referenced bolted tank with a 40 PSF roof live load


EXCLUSIONS: 
Permits, Fees, Taxes, Freight, Duties, Freight Forwarder, Unloading, Installation, Ladders, Level Indicators, Railing, Insulation, Concrete or Gravel Foundation, Grade Band, Signage, Grout, Transducers, Special Inspections, Level Switch, Process Piping, Over-Excavation or Recompaction of Existing Soils, Probes, Internal Vortex Breakers, Transmitters, Subgrade, Alarms, Blinds, Flex Coupling, Flap Valves, Freeze Protection, Heater, Heat Tape, Instrumentation, Float Valves or Switches, Downcomers or Supports thereof (Except Where Specified Above), Flex Tends, Valves, Meters, Grading, Gauges, Flap Gates, Water to Hydro-Test or Vacuum Test or Disposal thereof, Bact-T or V.O.C. Tests, Electrical Wiring or Controls thereof, Conduits, Surveying, External or Internal or Below Grade Piping, Fittings, Bonding or Internals or items not specifically mentioned above.

Show Less

5- 500 Imp Gallon tanks built as follows:
4' diameter x 6' long
• 500 Imperial gallon nominal capacity
• Double wall, steel tank
• 2 - lifting lugs
• Base skid w/ enclosure protruding 18" on one end to enclose CataDyne heaters (heater by others) Enclosure to have vents and double doors.
• HR steel
• 10-gauge primary head/12-gauge secondary head
• .083" thick primary/secondary shells
• Double pneumatic air/soap leak test to 24 Oz.


Nozzle Description:
• All nozzles A105N 150# RFWN flanges welded directly into tank
• All couplings A105N 3000#
• 2- 2" flanges c/w Kenco 5700 mechanical level gauge
• 2- 2" flanges (Inlet & Outlet)
• 1- 2" flange (HLSD)
• 1- 6" flange c/w 6" gooseneck & screen
• 1- 20"D round manway w/ 1 piece neoprene gasket and Grade 5 bolt-up


Tank Finish:
• Tank External (including bottom): blast, prime, 1.5" urethane foam
• Dress- install all accessories, flanges & covers including gaskets
and bolt-ups. Temporary shipping covers on all openings.
Price includes Solidworks CAD dwg with 2 revisions.

Show Less

There are currently no details for this product.

Show Less

5- 500 Imp Gallon tanks built as follows:
4' diameter x 6' long
• 500 Imperial gallon nominal capacity
• secondary containment to hold 10% of this Volume for BC, AB compliance for double-walled tanks
• Double wall, steel tank
• 2 - lifting lugs
• Base skid w/ enclosure protruding 18" on one end to enclose CataDyne heaters (heater is separate) enclosure to have vents and double doors.
• 316 stainless steel primary tank
• A1101 carbon steel secondary tank
• A36 structural components, enclosure
• 10-gauge primary head/12-gauge secondary head
• 12 gauge thick primary/secondary shells
• Double pneumatic air/soap leak test to 24oz


Nozzle Description:
• All nozzles A105N 150# flanges and A106B smls sch 40 pipe
• All couplings A105N 3000#
• 2- 2" flanges c/w Kenco 5700 mechanical level gauge
• 2- 2" flanges (Inlet & Outlet)
• 1- 2" flange (HLSD)
• 1- 6" flange c/w 6" gooseneck & screen
• 1- 20"D round manway w/ 1 piece neoprene gasket and Grade 5 bolt-up


Tank Finish:
• Tank External (including bottom): blast, prime, 1.5" urethane foam
• Dress- install all accessories, flanges & covers including gaskets
and bolt-ups. Temporary shipping covers on all openings
ade 5 bolt-up


Gauge:
Included in this quote is a Kenco Rate Gauge
The 5700 rate gauge has 1/2" MNPT x 3/8" FNPT threaded process
connections. 1/2" to 2" flanged process connections are also available.
The standard sight tube is 5/8" O.D. glass. 
The armored design of the gauge offers maximum protection for the sight
tube from mechanical impact. Three sides of the gauge are protected with
a metal frame, while the face of the gauge is protected with an impact
resistant polycarbonate shield.


Note, substitute gauges are available as a no cost option if end-user prefers.


Typical delivery is 8-10 wks a.r.a.d.

Show Less

5- 500 Imp Gallon tanks built as follows:
4' diameter x 6' long
• 500 Imperial gallon nominal capacity
• secondary containment to hold 10% of this Volume for BC, AB compliance for double-walled tanks
• Double wall, steel tank
• 2 - lifting lugs
• Base skid w/ enclosure protruding 18" on one end to enclose CataDyne heaters (heater is separate) enclosure to have vents and double doors.
• 316 stainless steel primary tank
• A1101 carbon steel secondary tank
• A36 structural components, enclosure
• 10-gauge primary head/12-gauge secondary head
• 12 gauge thick primary/secondary shells
• Double pneumatic air/soap leak test to 24oz


Nozzle Description:
• All nozzles A105N 150# flanges and A106B smls sch 40 pipe
• All couplings A105N 3000#
• 2- 2" flanges c/w Kenco 5700 mechanical level gauge
• 2- 2" flanges (Inlet & Outlet)
• 1- 2" flange (HLSD)
• 1- 6" flange c/w 6" gooseneck & screen
• 1- 20"D round manway w/ 1 piece neoprene gasket and Grade 5 bolt-up


Tank Finish:
• Tank External (including bottom): blast, prime, 1.5" urethane foam
• Dress- install all accessories, flanges & covers including gaskets
and bolt-ups. Temporary shipping covers on all openings
ade 5 bolt-up


Gauge:
Included in this quote is a Kenco Rate Gauge
The 5700 rate gauge has 1/2" MNPT x 3/8" FNPT threaded process
connections. 1/2" to 2" flanged process connections are also available.
The standard sight tube is 5/8" O.D. glass. 
The armored design of the gauge offers maximum protection for the sight
tube from mechanical impact. Three sides of the gauge are protected with
a metal frame, while the face of the gauge is protected with an impact
resistant polycarbonate shield.


Note, substitute gauges are available as a no cost option if end-user prefers.


Typical delivery is 8-10 wks a.r.a.d.

Show Less

1- 550 Bbl rectangular tank built to API 12F standards including the following,

General:
10'W x 30'L x 8'H 
• 8 Oz. design pressure
• -10 deg F to 250 deg F
• Steel Grade G40.21-13, ASTM A36/ASME SA36-10/112 
• 1/4" floor and walls
• 3/16" roof
• 4- lifting lugs
• 1- ladder
• 1- name plate

Skid:
• Tank to be welded to a 10 x 22 WF beam skid w/ lifting/winching pipe on both ends

Testing:
• Double pneumatic air/soap leak test to 12 Oz.

Nozzle Description:
• All nozzles A105N 150# RFSO flanges with A106B smls sch 40 pipe
• All couplings A105N 3000#
• 3- 3" nozzles
• 1- 4" nozzle
• 1- std 8" thief hatch connection
• 24" x 36" std manway w/ 1-piece neoprene gasket and Grade 5 bolting

Delivery: 8 weeks starting after confirmation of:
order, options, receipt of deposit, approved IFC drawings, and shop availability.

Show Less

1-750BBL single containment tank  15'3” x 24’ high
Tank contains the following:
Roof 1/4” A36
Shell 1/4” A36 (first course_
Shell 3/16” A36 (remaining three courses)
Floor 1/4” A36
Built to API 650 Modified Specifications
16 ounce non-engineered design - Tested to 24 oz
Radiography at cost plus 20%
Material – API 650 Group IIIA normalized
G40.21-04 , 38W/44W, ASTM
A36/ASME SA36-10/11
MDMT -40 degrees F


NOTE:
This material has been manufactured , tested and found to meet the specifications and purchase order requirements regarding structural quality coil for conversion to:
 * CSA G40.21-04 Grade 38W/44W
 * ASTM A36
 *ASME SA36-10-11 ADD
These designations meet all the material requirements of API650 (12th Edition) Group III - Killed Fine Grain Practice


15'3” dia x 24’ tall built to API 12F/API 650 MODIFIED
Thief hatch flange (thief hatch options below)
Gauge board fittings and brackets (gauge board options below)
nozzles as adders (see below)
no piping included
3” threaded near ladder for HLSD
4” center roof vent c/w 180 and bird screen
24” x 48” sidewall manway
Caged Ladder (OH&S)
4 lift lugs
1 tailing lug
4 hauling pads
grounding lug


As per attached drawing OilPro Stock 750BBL BARE REV B
Final price to be confirmed on approved drawings


GENERAL COMMENTS
1. The above quoted ladder assembly has been engineered to comply with OH & S -
Process Industry Practices standard STF05501 for fixed ladders and cages.
Please Note:
•30 feet is the limit for a single ladder with cage only.
•Two options for taller ladder are:
-Multiple offset ladder sections with landings at the transition points.
-Single ladder with fall arrest system (note cage is also not required if fall arrest
system is used)
2. Roof to shell joint will be seal welded on the outside only as per API 650,
Appendix F, and Detail B. For internally coated tanks, coating of the shell to roof
joint must be grouted prior to coating and therefore grout will be used for repair of voids. (Note: This does not follow NACE RP-0178 figure A.7.)
3. We have made no provision for nozzle loading calculations.
4. We have not allowed for any engineering or drafting changes. Any changes will be
charged a rate of $90.00 per hour for drafting and $120.00 per hour for engineering
with a minimum charge of two hours per drawing affected. This will also affect the
above quoted delivery.
5. All standard accessories and appurtenances will be shipped loose unless
otherwise stated. Customer is responsible for ensuring that all connections,
including manway nuts and bolts are tightened and equipment is inspected prior to it
being put into commission.
6. Unless otherwise stated above radiography has not been included. If fittings are
placed on or near seams and therefore require extra radiography as per API 650
5.7.3.4 11th Edition, extra costs will apply.
7. When tanks are coated we recommend the customer upgrade to stainless steel
couplings. Upgrade pricing is available upon request

Show Less

P-EVBI401+-2Wx3H-DUALHEAT:
Bolt-in Enviro Vault

c/w two heater stands and forklift
brackets. Vault will have the face and interior

sandblasted and painted.
P-EVH2424: 24x24 Enviro
Vault Assembly - CataDyne

heater c/w temperature controller, H19
tamper

resistant safety shut off valve, &
Fisher 912 low pressure

regulator, assembled as per Enviro Vault

drawings. Heater brackets included. Two (2)
heaters recommended.
P-EVWP: 12 VDC Wiring
package. Consisting of 5' of

Teck cable, junction box, 30' of 10 gauge
SOW cable

c/w battery clips along with required seals
for

connecting the heater in a hazardous area
P-EVBI-SLPR: Additional
Sleeper Material (per inch)
P-EVBI-COATING:
Sandblast and apply Devoe 253

coating to "wetted" area of vault

Notes:

• Bolt-ins come with 1" of sleeper
material suitable for a flush mounted tank;

additional sleeper material will be charged
as per line item #4.

• This bolt-in is not for use in tanks over
32' in height

Show Less

One (1) 750 BBL single walled tank 15'-3" x 24'-0" high
•             750 Bbl nominal capacity single wall, steel tank
•             12 Oz Maximum Pressure Design capable (See anchor chair options below, as some engineered versions may require anchoring to be 16 Oz rated)
•             Double pneumatic leak tested to 24 Oz
•             Floor thickness:1/4"
•             Shell and roof thickness: 3/16"
•             Minimum Design Temperature: -40 degrees F
•             Steel is G40.21-04 , 38W/44W, ASTM A36/ASME SA36-10/11, also meeting requirements of API 650 Group III                   
Additional Fittings included:
•             27' Caged Ladder (see note 1 below and price list for detail on OH&S Compliance options)
•             four (4) - lifting lugs
•             one (1) - tailing lug
•             Transportation stops (hauling pads)
•             Piping is not included with base tank. We will accommodate your internal or external piping as required, including custom internals.
Nozzle Description:
•             Three (3) - TBD" couplings for Level Gauge connections (two guide wire connections, one float wire connection, with coupling sizes automatically matched to gauge board model chosen in options below)
•             One (1) - 8" Standard thief hatch API connection (thief hatch options below) 
•             One (1) - 4" coupling on center roof (Can be up-sized if required, per attached pricelist)
•             One (1) - 24" x 36" API Standard manway c/w one-piece neoprene gasket (includes pre-delivery bolt-up)
•             All flanged nozzles to be A105N 150# RFSO with A-106B SCH 40 seamless pipe unless otherwise selected in options list)
•             All couplings to be A105N 3000# unless otherwise stated
•             Please see price list for per-nozzle pricing to customize tank
GENERAL COMMENTS:
Pricing comments: 
a. As of late January/early February, steel mills are consistently raising prices on us on a weekly basis, and therefore we currently are only able to guarantee pricing for a period of 1 week unless explicitly stated otherwise in separate quote terms. We are seeing price increases for steel of as much as 50% and simply cannot absorb such fluctuations. (FYI: Steel is typically about 1/3 the cost of a tank) Likewise, price decreases will be passed on as they occur and the market settles down.
Technical Comments:
1. The above included ladder assembly may not comply with OH&S - Process Industry Practices standard STF05501 for fixed ladders and cages. Prices for an upgrade are available in options below. 
2. Roof to shell joint will be seal welded on the outside only as per API 650, Appendix F, and Detail B. For internally coated tanks, coating of the shell to roof joint must be grouted prior to coating and therefore grout will be used for repair of voids. (Note: This does not follow NACE RP-0178 figure A.7.) 
3. We made no provision for nozzle loading calculations and these are not included in the base tank price. 
4. A: We have not allowed for drafting changes beyond Revision 1. We therefore recommend you review initial markups thoroughly. Any further changes will be charged a rate of $90.00 per hour with a minimum charge of two hours per drawing affected. Changes made after IFC (Issued For Construction) stage may affect delivery.
4. B: We have not allowed for changes requiring engineering reviews. Changes will be charged a rate of $120.00 per hour with a minimum charge of two hours per drawing affected. Changes made after IFC stage may affect delivery. 
5. All standard accessories and appurtenances will be shipped loose unless otherwise stated. Installer is responsible for ensuring that all connections, including manway nuts and bolts are tightened and equipment is inspected prior to it being put into commission. 
6. Unless otherwise stated above, radiography is not included. If fittings are placed on or near seams and therefore require extra radiography per API 650 5.7.3.4 11th Edition, extra costs will apply. 
7. When tanks are coated, we recommend the customer upgrade to stainless steel couplings. Upgrade pricing is included in the price list below.

Show Less

1-750BBL single containment tank 15'3” x 24’ high
Tank shell built as follows:
Roof 3/16” A36
Shell 3/16” A36 
Floor 1/4” A36
Built to API 650 Modified Specifications
16 ounce non-engineered design - Tested to 24 oz
Radiography at cost plus 20%
Material – API 650 Group IIIA normalized
G40.21-04 , 38W/44W, ASTM
A36/ASME SA36-10/11
MDMT -40 degrees F


NOTE:
This material has been manufactured , tested and found to meet the specifications and purchase order requirements regarding structural quality coil for conversion to:
 * CSA G40.21-04 Grade 38W/44W
 * ASTM A36
 *ASME SA36-10-11 ADD
These designations meet all the material requirements of API650 (12th Edition) Group III - Killed Fine Grain Practice


15'3” dia x 24’ tall built to API 12F/API 650 MODIFIED
Thief hatch flange (thief hatch options below)
Gauge board fittings and brackets (gauge board options below)
nozzles as adders (see below)
no piping included
3” threaded near ladder for HLSD
4” center roof vent c/w 180 and bird screen
24” x 48” sidewall manway
Caged Ladder (OH&S)
4 lift lugs
1 tailing lug
4 hauling pads
grounding lug


As per drawing OilPro Stock 750 BBL BARE REV B
Final price to be confirmed on approved drawings and on confirmation of options chosen.

Show Less

RE: 1-750BBL single containment tank 15'3" x 24' high
Tank contains the following:
Roof 3/16 A36
Shell 3/16 A36
Floor %u00BC A36
Built to API 650 Modified Specifications
16 ounce non-engineered design - Tested to 24 oz
MDMT -40 degrees F
Material - API 650 Group IIIA normalized

15'3" dia x 24' tall built to API 650 MODIFIED
Thief hatch flange (thief hatch options below)
Gauge board fittings and brackets (gauge board options below)
no piping included
3" threaded near ladder for HLSD
4" center roof vent c/w 180 and bird screen
24" x 36" sidewall manway
Caged Ladder (OH&S)
4 lift lugs
1 tailing lug
4 hauling pads

750-Ext-SSPC-SP6-INS
SSPC - SP6 Blast, prime and apply 1 1/2" urethane Foam insulation and 2 coats
black elastomeric coating (other color choice may increase overall price do to number
of coatings needed to cover)
Underside of tank not included.

THIEF-SWEET-16Oz
Hawkeye Model 200 TVTH Sweet Service Thief Hatch
(Part # TVTH200) c/w 8" API flange - available in 4, 8, &
16 oz pressure configurations

750-GAUGE-24'-SWEET-STD
Hawkeye Model 750 Gauge Head System - 24' Tank (Part
# M750-24) c/w Model 750 gauge head, gauge board w/decal, standard indicator &
guide kit, and float guide kit

Nozzle-6-150-RFSO-DFF: 6" 150# RF slip on, Double flange face
Nozzle-4-150-RFSO-DFF: 4" 150# RF slip on, Double flange face
Nozzle-4-150-RFSO-SFF: 4" 150# RF Slip on, Single flange face
Anchor Chair-8-Weld: 8 Chair Anchor Set (Welded)

Show Less

RE: 1-750BBL single containment tank 15'3" x 24' high
Tank contains the following:
Roof 3/16 A36
Shell 3/16 A36
Floor %u00BC A36
Built to API 650 Modified Specifications
16 ounce non-engineered design - Tested to 24 oz
MDMT -40 degrees F
Material - API 650 Group IIIA normalized

15'3" dia x 24' tall built to API 650 MODIFIED
Thief hatch flange (thief hatch options below)
Gauge board fittings and brackets (gauge board options below)
no piping included
3" threaded near ladder for HLSD
4" center roof vent c/w 180 and bird screen
24" x 36" sidewall manway
Caged Ladder (OH&S)
4 lift lugs
1 tailing lug
4 hauling pads

750-Ext-SSPC-SP6-INS
SSPC - SP6 Blast, prime and apply 1 1/2" urethane Foam insulation and 2 coats
black elastomeric coating (other color choice may increase overall price do to number
of coatings needed to cover)
Underside of tank not included.

THIEF-SWEET-16Oz
Hawkeye Model 200 TVTH Sweet Service Thief Hatch
(Part # TVTH200) c/w 8" API flange - available in 4, 8, &
16 oz pressure configurations

750-GAUGE-24'-SWEET-STD
Hawkeye Model 750 Gauge Head System - 24' Tank (Part
# M750-24) c/w Model 750 gauge head, gauge board w/decal, standard indicator &
guide kit, and float guide kit

Nozzle-6-150-RFSO-DFF: 6" 150# RF slip on, Double flange face
Nozzle-4-150-RFSO-DFF: 4" 150# RF slip on, Double flange face
Nozzle-4-150-RFSO-SFF: 4" 150# RF Slip on, Single flange face
Anchor Chair-8-Weld: 8 Chair Anchor Set (Welded)

Show Less

RE: 1-750BBL single containment tank 15'3" x 24' high
Tank contains the following:
Roof 3/16 A36
Shell 3/16 A36
Floor %u00BC A36
Built to API 650 Modified Specifications
16 ounce non-engineered design - Tested to 24 oz
MDMT -40 degrees F
Material - API 650 Group IIIA normalized

15'3" dia x 24' tall built to API 650 MODIFIED
Thief hatch flange (thief hatch options below)
Gauge board fittings and brackets (gauge board options below)
no piping included
3" threaded near ladder for HLSD
4" center roof vent c/w 180 and bird screen
24" x 36" sidewall manway
Caged Ladder (OH&S)
4 lift lugs
1 tailing lug
4 hauling pads

750-Ext-SSPC-SP6-INS
SSPC - SP6 Blast, prime and apply 1 1/2" urethane Foam insulation and 2 coats
black elastomeric coating (other color choice may increase overall price do to number
of coatings needed to cover)
Underside of tank not included.

THIEF-SWEET-16Oz
Hawkeye Model 200 TVTH Sweet Service Thief Hatch
(Part # TVTH200) c/w 8" API flange - available in 4, 8, &
16 oz pressure configurations

750-GAUGE-24'-SWEET-STD
Hawkeye Model 750 Gauge Head System - 24' Tank (Part
# M750-24) c/w Model 750 gauge head, gauge board w/decal, standard indicator &
guide kit, and float guide kit

Nozzle-6-150-RFSO-DFF: 6" 150# RF slip on, Double flange face
Nozzle-4-150-RFSO-DFF: 4" 150# RF slip on, Double flange face
Nozzle-4-150-RFSO-SFF: 4" 150# RF Slip on, Single flange face
Anchor Chair-8-Weld: 8 Chair Anchor Set (Welded)

Show Less

RE: 1-750BBL single containment tank 15'3" x 24' high
Tank contains the following:
Roof 3/16 A36
Shell 3/16 A36
Floor %u00BC A36
Built to API 650 Modified Specifications
16 ounce non-engineered design - Tested to 24 oz
MDMT -40 degrees F
Material - API 650 Group IIIA normalized

15'3" dia x 24' tall built to API 650 MODIFIED
Thief hatch flange (thief hatch options below)
Gauge board fittings and brackets (gauge board options below)
no piping included
3" threaded near ladder for HLSD
4" center roof vent c/w 180 and bird screen
24" x 36" sidewall manway
Caged Ladder (OH&S)
4 lift lugs
1 tailing lug
4 hauling pads

750-Ext-SSPC-SP6-INS
SSPC - SP6 Blast, prime and apply 1 1/2" urethane Foam insulation and 2 coats
black elastomeric coating (other color choice may increase overall price do to number
of coatings needed to cover)
Underside of tank not included.

THIEF-SWEET-16Oz
Hawkeye Model 200 TVTH Sweet Service Thief Hatch
(Part # TVTH200) c/w 8" API flange - available in 4, 8, &
16 oz pressure configurations

750-GAUGE-24'-SWEET-STD
Hawkeye Model 750 Gauge Head System - 24' Tank (Part
# M750-24) c/w Model 750 gauge head, gauge board w/decal, standard indicator &
guide kit, and float guide kit

Nozzle-6-150-RFSO-DFF: 6" 150# RF slip on, Double flange face
Nozzle-4-150-RFSO-DFF: 4" 150# RF slip on, Double flange face
Nozzle-4-150-RFSO-SFF: 4" 150# RF Slip on, Single flange face
Anchor Chair-8-Weld: 8 Chair Anchor Set (Welded)

Show Less

Reconditioned Sweet Service 100bbl Dual Wall Storage tank

1.0 TANK SPECIFICATIONS
Manufactured by Nusco in 2006

DESCRIPTION
100 Barrel Dual Walled
Nominal Dimensions: 9'6" Diameter x 8'0" High
Manway: 20" round
Thief Hatch: Yes
Gauge Board: Yes
Ladder: Yes

CONNECTIONS
Gauge Board %u00BE" collar
Inlet: 2" NPT
Truck out: 3" NPT
HLSD: 2" NPT
Interstitial Space: %u00BE" collar
Thief Hatch 8" flange
Vent 3" NPT
Drain 2" NPT

2.0 SKID AND BUILDING SPECIFICATIONS

1 FOAM PANEL METAL BUILDING
3'0" Wide x 3'0" Long x 3'0" High
22 Gauge exterior / Galvanized interior

1 SKID BASE 8'0" WIDE x 12'0" LONG
One (1) 8'0" Wide x 12'0" Long
4" Channel Main members
2" angle cross members
Lift lugs

1 BUILDING HEATER
12" x 24" Catalytic type heater c/w the following;
25 feet of 12 VDC start cables. Natural Gas Orifice

3.0 PAINT AND COATING SPECIFICATIONS
External Preparation SSPC-SP#3
External Finish Existing
Insulation Polyurethane Spray Foam

Show Less

There are currently no details for this product.

Show Less

400 Bbl tank custom-built for New Zealand and Australian markets
Oilfield tank with the following features:
• 400 Bbl nominal design capacity (approx. 63 m3)
• Connections (All flanges built in accordance with ANSI B16.5):
• N1: 4" 150 RFSO
• N2: 4" 150 RFSO
• N4: 4" 150 RFSO
• N5: 4" 150 RFSO
• N6: 3" 150 RFSO
• C1: 2" 3000# full coupling
• C2: ½" 3000# full coupling
• C3: ½" 3000# full coupling
• C4: ½" 3000# full coupling
• C5a/b/c: %u00BE" 3000# full coupling
• C6: 2" 3000# full coupling
• DC: 3" Pipe Downcomer
• M1: 24" 985 Std API Round Manway
• TH: 8" API flanged connection Thief/Dip Hatch
• 39" round Inspection Manway
• 8.0" Thief Hatch

Note: all openings blanked with temporary shipping covers unless specified.

Features, cont'd:
• Heavy Duty L-Type Skid for easy handling/transport/setting c.w.:
• Crossbars
• Pull-bars
• lifting lugs
• Tank repads for additional support
• Grounding lug (earth boss)
• External ladder, cage and rooftop hand rail, HSNO compliant design
• External Gauge, mechanical type, c.w.:
• Stainless Steel float and swivel
• Bright red indicator for high visibility
• Aluminum framed gauge board with reflective, durable, white 3M decal (m3 readout)
• Gauge board slides on UHMW runners for smooth operation
• gauge head c.w. double pulley assembly, Stainless Steel cable.
• Float is cable guided, guides anchored for accuracy and durability
• Thief/Dip Hatch:
• C&B 8" Sweet Service Thief Hatch
• 8 Oz Pressure, 0.4" Oz Vacuum
• Buna base Gasket
• mounting hardware
• HSNO Compliant Nameplate
• MTR's for Plate, piping and flanges included
• Designed and built for the following operating conditions:
• Operating Pressure: Atmospheric
• 0.175 kPa (0.4 Oz) Vacuum
• 6 kPa (13.9 Oz) Pressure
• tested to 105 kPa (24.4 Oz)
• -29%u00B0 Celsius
• Design Code AS1692-2006, Category 5
• Weight full of water: 8,719 kg
• Weight empty 5,719 kg
• Dimensions 
• Nominal Height: 6.1 approx. meters (20')
• Transport Height: 4.13 m approx.(+ ladder and cage)
• Transport Width:     3.66 meters approx. plus ladder and cage
• Weight:     6.0 Tonne approx.
• Transportation:     Low Loader and a single crane with a Fly Hook

• Our NZ-spec tanks are built to Design Code AS1692-2006, Category 5 in compliance with NZ EPA requirements: 
• Schedule 8, Part 19, Clauses 94 & 95 of the Transfer Notice.
• Approved Fabricator Number FAB0054
• HS Class 3.1A
• Tank Design No. TNK 13074
• Test Certificate issued pursuant to Section 82 of the Hazardous Substances and New Organisms Act of 1996
• Approved for storage and transfer of Crude or Condensate having a Hazard Classification of:3.1A, 6.1E, 6.3B, 6.7B, 9.1

Show Less

There are currently no details for this product.

Show Less