1A
CONTINENTAL CL1CL8-CDY SERIES PROGRESSIVE CAVITY PUMP%u00A0
- MODEL: CL1CL8-CDY PUMP%u00A0
- CAST IRON CASTING%u00A0
- ALLOY STEEL INTERNALS%u00A0
- HARD CHROME PLATED ROTOR AND SHAFT%u00A0
- HNBR STATOR%u00A0
- 4.0" ANSI 150# FF SUCTION FLANGE AND 4.0" FNPT DISCHARGE FLANGE%u00A0
- SINGLE COMPONENT MECH. SEAL (SIC/C/SS)%u00A0
- API PLAN 02 SEAL FLUSH
2A
MARATHON TEFC ELECTRIC MOTOR%u00A0
- MODEL GT1011A%u00A0
- 2 HP, 3PH/50HZ/1190-380V, 1000 RPM
TEFC ENCLOSURE%u00A0
- FRAME SIZE 213T%u00A0
- CLASS F INSULATION%u00A0
- CLASS I DIVISION II CLASSIFICATION, IP55
VFD COMPATIBLE
3A
TOP MOUNT, V-BELT DRIVE, PUMP UNITIZATION SKID INCLUDES:%u00A0
- CARBON STEEL PUMP SKID%u00A0
- NON-SPARKING LIGHT WEIGHT ALUMINUM V-BELT GUARD%u00A0
- MOTOR/PUMP ALIGNMENT
STRUCTURAL SKID TO BE SANDBLASTED & PAINTED IN ACCORDANCE SSPC-SP6 (COMMERCIAL BLAST GRADE)
SKID PAINT TO BE UPGRADED FROM TYPICAL RUSTEX PRIMER AND INDUSTRIAL ENAMEL TOP COAT TO
1 COAT OF CLOVERDALE DURA PRIME EPOXY PRIMER @
2 - 3 MILS DFT. AND
2 COATS OF WARM GREY CLOVERDALE ARMOR SHIELD XP ALIPHATIC URETHANE TOP COAT @ 2 - 3 MILS DFT
4A
V-BELT DRIVE FOR THE ABOVE PUMP AND MOTOR%u00A0
- THE PUMP WILL BE SIZED FOR APPROXIMATELY 170 RPM THEREFORE A SHEAVE TURN DOWN RATIO OF APPROXIMATELY 5.88:1 WILL BE SUPPLIEDOptions
5A
OPTIONAL COST ADDER%u00A0
(QTY 1 REQUIRED) FOR A PSV SIZED FOR BLOCKED FLOW MERCER PRESSURE RELIEF VALVE%u00A0
- MODEL# 91-17C71T06BX1 (SIZED FOR A BLOCKED FLOW OF ~ 16 GPM)%u00A0
- SET @ 1241 KPAG (180 PSIG) LIQUID SERVICE
ASSUMED NO BP%u00A0
- RATED FOR A MAX CAPACITY OF APPROX 23 USGPM @ 180 PSIG%u00A0
- 1.0" MNPT X 1" FNPT%u00A0
- C ORIFICE%u00A0
- CONVENTIONAL DESIGN%u00A0
- 316 SS BODY
INLET BASE
BONNET
DISC AND NOZZLE%u00A0
- INCONEL X750 SPRING%u00A0
- NACE MR0175 COMPLIANT%u00A0
- SHIPPED LOOSE%u00A05B
OPTIONAL COST ADDER%u00A0
(QTY 1 REQUIRED) FOR A HIGH PRESSURE SWITCH
CCS 6900GZE18 HIGH PRESSURE SWITCH%u00A0
- INCREASING - 45 - 375 PSIG INCREASING SET PRESSURE%u00A0
- 316 SS CONSTRUCTION
1/2" NPT CONNECTION%u00A0
- CLASS 1 DIVISION 1
EXPLOSION PROOF%u00A0
- SET PRESSURE IS 80 PSIG%u00A0
- SHIPPED LOOSE%u00A0Application Data:
LIQUID
Skimmer water
Flow Rate
16 USGPM (Pump sized for 5 USGPM)
Suction Pressure:
0-20 psig assumed
Differential Pressure:
assumed approximately 10 psi (used 30 psi as worst case)
Required HP:
approx. 0.99 HP at design point (2 HP motor quoted)
s.g.:
Assumed 1.10%u00A0
Viscosity:
Assumed approx. 1.0 cP
Temperature:
95 deg. F
NPSHa:
assumed minimal
NPSHr:
approx 1.5' of head at design point (170 rpm)
H2S content:
assumed minimal
Solids content
assumed minimal
Area Classification:
Assumed Class 1 Div II, 190V, 50 Hz
Service duty:
Assumed Continuous
Contaminants:
Assumed minimal
Show Less
