E-101A/B/C: Shell/tube:
12" x 40' Gas/Gas Exchangers
Shell tube (NEN-type) with:
? 2,000 psi tube MAWP @ -20F/200F
? Shell rated for -20/150F
? 83 x %u00BE" 14 BWG SA 179 tubes
? SA 106 B shell
? SA516-70N Heads
? 3.2 mm c.a.
? Built in 2000
? Inlet piping is currently 4" swaged up to 6" inlet on exchangers
? Outlets from exchangers are :
o 6" 900 ANSI tube side
o 6" 600 ANSI shell side
Choke is 2" 900 ANSI Fail Close


H-100: Indirect Heater
Line Heater
100,000 BTU/hr
1349 psi MAWP
-20/200 F
10 coils preheat and 6 coils preheat
Process coils are 2" 600 ANSI
Fuel gas preheat lines
1.6 mm c.a.
Built in 2000


H-300
Glycol Reboiler
BTU/hr TBA


V-100 LTS
3 phase horizontal c.w. 18" boot
42" x 10' s/s
1414 psi MOP
-49F/149F
Built in 2000
1.6 c.a.
SA516-70N Head and Shell mat'l
18" manway
18" water boot
6" inlet
Externally caged LC and LGs for liquid boot and vessel interfaces


V-300
Glycol Flash Separator
3 phase, vertical
19.25" ID x 6'-6" s/s
150 PSI
-20/203F
Built in 2000
1.6 c.a.
SA 516-70N Head and Shell mat'l


P-300/301
Glycol Charge Pumps
Electric


F-300/301
Glycol particulate/Carbon filters


Process simulation runs and data sheets on hand

Show Less

Condition fuel or flare gas:
OilPro's Liquid Stripper design drops, captures, and monetizes typical flare stack or tank vent "wet" gas liquids. The remaining conditioned gas is OEM spec fuel for on-site generation equipment or delivers a clean burning flare. Power use includes site needs, grid sales, or data operations. Valuable condensate is monetized and engines run optimally.

Condition injection gas:
The Micro Refrigeration Unit strips liquids and conditions injection gas for optimal results. Monetize condensate while improving injection gas. Results include better injection performance and fewer downhole equipment issues caused by condensates.

Feature overview:
- Minimal package footprint with compact, engineered components
- Simple, durable refrigeration system, serviceable by HVAC technicians  
- Refrigerant is safer than propane, reduces on-site hazards
- Low temp. separator (LTS) for improved separation
- High quality, common brand component metallurgy and trim

Liquid Recovery Unit-20 HP-New
Designed for 500-1300 MSCF/d total flow (Gas composition dependent)
Summary:
-40 deg F capable system

Skid Mounted, c.w.:
 Inlet coalescing vessel c.w.
  Filter

Packaged with 
 Controls
 H2S compatible materials
 Two Stainless steel heat exchangers
 Liquid dump valve
 2" SCH 40 inlet and outlet piping for gas
 1" SCH 40 Product outlet 

Electrical:
 Single Phase
 480 Volt

Major Component Description:
AC-1000: Refrigerant Condenser
 1/2" tubing c.w. 
 fins for optimized heat dispersion

V-1: Inlet Knockout/Coalescer combination vessel
 Custom sized for application.
 MAWP: 245 psig @ 250 deg F
 MDMT: -40 deg F @ 245 psig
 Coalescer, custom design
 ASME Sec. VIII Div. 1 design
 NB Registered

C-100: Refrigeration Unit
 Scroll compressor
 MAWP: 415+ PSIG @ -40 deg F
 Refrigerant 448A
 20 HP/ ?? A/ 60 Hz/ single phase

V-100: Receiver:
 Sized for application
 MAWP 450 PSIG
 6' x 18"

E-1: Gas/Gas Exchanger
 MAWP: 675 PSIG
 ~ ??+ BTU/hr design rate
 316 SS construction

E2: Chiller
 MAWP 675 PSIG
 316 SS construction

E3: Pre-Cooler
 Liquid to gas exchanger (Refrigerant)
 MAWP 675 PSIG
 tube and tube configuration

V2: Cold Separator
 875 PSIG
 ~24" x 6' s/s
 304 SS tubes, 0.125" walls

Customer to supply:

Option:
1.
 Inlet filter, mounted to skid c.w. bypass, filter element.

Show Less

Condition fuel or flare gas:
OilPro's Liquid Stripper design drops, captures, and monetizes typical flare stack or tank vent "wet" gas liquids. The remaining conditioned gas is OEM spec fuel for on-site generation equipment or delivers a clean burning flare. Power use includes site needs, grid sales, or data operations. Valuable condensate is monetized and engines run optimally.

Condition injection gas:
The Micro Refrigeration Unit strips liquids and conditions injection gas for optimal results. Monetize condensate while improving injection gas. Results include better injection performance and fewer downhole equipment issues caused by condensates.

Feature overview:
- Minimal package footprint with compact, engineered components
- Simple, durable refrigeration system, serviceable by HVAC technicians  
- Refrigerant is safer than propane, reduces on-site hazards
- Low temp. separator (LTS) for improved separation
- High quality, common brand component metallurgy and trim

Liquid Recovery Unit-20 HP-New
Designed for 500-1300 MSCF/d total flow (Gas composition dependent)
Summary:
-40 deg F capable system

Skid Mounted, c.w.:
 Inlet coalescing vessel c.w.
  Filter

Packaged with 
 Controls
 H2S compatible materials
 Two Stainless steel heat exchangers
 Liquid dump valve
 2" SCH 40 inlet and outlet piping for gas
 1" SCH 40 Product outlet 

Electrical:
 Single Phase
 480 Volt

Major Component Description:
AC-1000: Refrigerant Condenser
 1/2" tubing c.w. 
 fins for optimized heat dispersion

V-1: Inlet Knockout/Coalescer combination vessel
 Custom sized for application.
 MAWP: 245 psig @ 250 deg F
 MDMT: -40 deg F @ 245 psig
 Coalescer, custom design
 ASME Sec. VIII Div. 1 design
 NB Registered

C-100: Refrigeration Unit
 Scroll compressor
 MAWP: 415+ PSIG @ -40 deg F
 Refrigerant 448A
 20 HP/ ?? A/ 60 Hz/ single phase

V-100: Receiver:
 Sized for application
 MAWP 450 PSIG
 6' x 18"

E-1: Gas/Gas Exchanger
 MAWP: 675 PSIG
 ~ ??+ BTU/hr design rate
 316 SS construction

E2: Chiller
 MAWP 675 PSIG
 316 SS construction

E3: Pre-Cooler
 Liquid to gas exchanger (Refrigerant)
 MAWP 675 PSIG
 tube and tube configuration

V2: Cold Separator
 875 PSIG
 ~24" x 6' s/s
 304 SS tubes, 0.125" walls

Customer to supply:

Option:
1.
 Inlet filter, mounted to skid c.w. bypass, filter element.

Show Less

Condition fuel or flare gas:
OilPro's Liquid Stripper design drops, captures, and monetizes typical flare stack or tank vent "wet" gas liquids. The remaining conditioned gas is OEM spec fuel for on-site generation equipment or delivers a clean burning flare. Power use includes site needs, grid sales, or data operations. Valuable condensate is monetized and engines run optimally.

Condition injection gas:
The Micro Refrigeration Unit strips liquids and conditions injection gas for optimal results. Monetize condensate while improving injection gas. Results include better injection performance and fewer downhole equipment issues caused by condensates.

Feature overview:
- Minimal package footprint with compact, engineered components
- Simple, durable refrigeration system, serviceable by HVAC technicians  
- Refrigerant is safer than propane, reduces on-site hazards
- Low temp. separator (LTS) for improved separation
- High quality, common brand component metallurgy and trim

Liquid Recovery Unit-30 HP-New
Designed for 1-2 MMSCF/d total gas flow and +- 150 Bbl/d of liquids recovery
Note: 
This skid flowrange variance is composition dependent and requiries verification by OilPro's process engineering team.
This option deletes the 5 HP upstream dehydrator section for cases where initial dewatering is not required or when higher methanol injection rates are acceptable.

Summary:
-40 deg F capable system

Skid Mounted, c.w.:
 Inlet coalescing vessel c.w.
  Filter

Packaged with single controls:
 30 HP Compressor c.w.
 - Two stainless steel heat exchangers
 - Liquid dump valve
 H2S compatible materials
 2" SCH 40 inlet and outlet piping for gas
 1" SCH 40 Product outlet 

Electrical:
 Single Phase
 480 Volt

Major Component Description:
AC-1000: Refrigerant Condenser
 1/2" tubing c.w. 
 fins for optimized heat dispersion

V-1: Inlet Knockout/Coalescer combination vessel
 Custom sized for application.
 MAWP: 245 psig @ 250 deg F
 MDMT: -40 deg F @ 245 psig
 Coalescer, custom design
 ASME Sec. VIII Div. 1 design
 NB Registered, CRN for Canadian applications

C-100: Refrigeration Unit
 Scroll compressor
 MAWP: 415+ PSIG @ -40 deg F
 Refrigerant 448A
 30 HP/ ??A/ 60 Hz/ single phase

V-100: Receiver:
 Sized for application
 MAWP 450 PSIG
 6' x 18"

E-1: Gas/Gas Exchanger
 MAWP: 675 PSIG
 design rate to match process conditions
 316 SS construction

E2: Chiller
 MAWP 675 PSIG
 316 SS construction

E3: Pre-Cooler
 Liquid to gas exchanger (Refrigerant)
 MAWP 675 PSIG
 tube and tube configuration

V2: Cold Separator
 875 PSIG
 ~24" x 6' s/s
 304 SS tubes, 0.125" walls

Customer to supply:
1. Two-phase separator
2. Cold Weather Enclosure
3. Methanol supply, pump and storage
 - Methanol Injection Pump
 - MAWP 1500 psig
 - ~20 USGPM/d capacity
 - 120VAC
4. Product storage tank
5. Outlet filter
 -mounted to skid c.w. bypass, filter element.

Show Less

Condition fuel or flare gas:
OilPro's Liquid Stripper design drops, captures, and monetizes typical flare stack or tank vent "wet" gas liquids. The remaining conditioned gas is OEM spec fuel for on-site generation equipment or delivers a clean burning flare. Power use includes site needs, grid sales, or data operations. Valuable condensate is monetized and engines run optimally.

Condition injection gas:
The Micro Refrigeration Unit strips liquids and conditions injection gas for optimal results. Monetize condensate while improving injection gas. Results include better injection performance and fewer downhole equipment issues caused by condensates.

Feature overview:
- Minimal package footprint with compact, engineered components
- Simple, durable refrigeration system, serviceable by HVAC technicians  
- Refrigerant is safer than propane, reduces on-site hazards
- Low temp. separator (LTS) for improved separation
- High quality, common brand component metallurgy and trim

Liquid Recovery Unit-30 HP-New
Designed for 900-1100 MSCF/d total flow.
Note: 
This skid's flowrange variance is gas composition dependent and requiries verification by OilPro's process engineering team.
This system includes a 5 HP upstream dehydrator section for cases where initial dewatering is required or end-users would like to mitigate methanol use.
Summary:
-40 deg F capable system

Skid Mounted, c.w.:
 Inlet coalescing vessel c.w.
  Filter

Packaged with dual controls:
A. 5 HP Dehydration section c.w.
 - 2 stainless steel heat exchangers
 - Liquid dump valve for above
B. 20 HP section c.w.
 - 2 stainless steel heat exchangers
 - Liquid dump valve for above
 H2S compatible materials
 2" SCH 40 inlet and outlet piping for gas
 1" SCH 40 Product outlet 

Electrical:
 Single Phase
 480 Volt

Major Component Description:
AC-1000: Refrigerant Condenser
 1/2" tubing c.w. 
 fins for optimized heat dispersion

V-1: Inlet Knockout/Coalescer combination vessel
 Custom sized for application.
 MAWP: 245 psig @ 250 deg F
 MDMT: -40 deg F @ 245 psig
 Coalescer, custom design
 ASME Sec. VIII Div. 1 design
 NB Registered, CRN for Canadian applications

C-100: Refrigeration Unit
 Scroll compressor
 MAWP: 415+ PSIG @ -40 deg F
 Refrigerant 448A
 20 HP/ ??A/ 60 Hz/ single phase

V-100: Receiver:
 Sized for application
 MAWP 450 PSIG
 6' x 18"

E-1: Gas/Gas Exchanger
 MAWP: 675 PSIG
 design rate to match process conditions
 316 SS construction

E2: Chiller
 MAWP 675 PSIG
 316 SS construction

E3: Pre-Cooler
 Liquid to gas exchanger (Refrigerant)
 MAWP 675 PSIG
 tube and tube configuration

V2: Cold Separator
 875 PSIG
 ~24" x 6' s/s
 304 SS tubes, 0.125" walls

Customer to supply:
1. Two-phase separator
2. Cold Weather Enclosure
3. Methanol supply, pump and storage
 - Methanol Injection Pump
 - MAWP 1500 psig
 - ~20 USGPM/d capacity
 - 120VAC
4. Product storage tank
5. Outlet filter
 -mounted to skid c.w. bypass, filter element.
 

Show Less

Condition fuel or flare gas:
OilPro's Liquid Stripper design drops, captures, and monetizes typical flare stack or tank vent "wet" gas liquids. The remaining conditioned gas is OEM spec fuel for on-site generation equipment or delivers a clean burning flare. Power use includes site needs, grid sales, or data operations. Valuable condensate is monetized and engines run optimally.

Condition injection gas:
The Micro Refrigeration Unit strips liquids and conditions injection gas for optimal results. Monetize condensate while improving injection gas. Results include better injection performance and fewer downhole equipment issues caused by condensates.

Feature overview:
- Minimal package footprint with compact, engineered components
- Simple, durable refrigeration system, serviceable by HVAC technicians  
- Refrigerant is safer than propane, reduces on-site hazards
- Low temp. separator (LTS) for improved separation
- High quality, common brand component metallurgy and trim

Liquid Recovery Unit-5 HP-New Designed for 100-250 MSCF/d total flow (Gas composition dependent) Summary: -40 deg F capable system Skid Mounted, c.w.: Inlet coalescing vessel c.w. Filter Packaged with Controls H2S compatible materials Two Stainless steel heat exchangers Liquid dump valve 2" SCH 40 inlet and outlet piping for gas 1" SCH 40 Product outlet Electrical: Single Phase 480 Volt Built for US Market P1: Methanol Injection Pump MAWP 1500 psig ~20 USGPM/d capacity 120VAC Major Component Description: AC-1000: Refrigerant Condenser 1/2" tubing c.w. fins for optimized heat dispersion V-1: Inlet Knockout/Coalescer combination vessel Custom sized for application. MAWP: 245 psig @ 250 deg F MDMT: -40 deg F @ 245 psig Coalescer, custom design ASME Sec. VIII Div. 1 design NB Registered C-100: Refrigeration Unit Scroll compressor MAWP: 415+ PSIG @ -40 deg F Refrigerant 448A 5 HP/ 30 A/ 60 Hz/ single phase V-100: Receiver: Sized for application MAWP 450 PSIG 6' x 18" E-1: Gas/Gas Exchanger MAWP: 675 PSIG ~ 70+ BTU/hr design rate 316 SS construction E2: Chiller MAWP 675 PSIG 316 SS construction E3: Pre-Cooler Liquid to gas exchanger (Refrigerant) MAWP 675 PSIG tube and tube configuration V2: Cold Separator 875 PSIG ~24" x 6' s/s 304 SS tubes, 0.125" walls Customer to supply: - Methanol tank - Methanol Option: 1. Inlet filter, mounted to skid c.w. bypass, filter element.

Show Less

Condition fuel or flare gas:
OilPro's Liquid Stripper design drops, captures, and monetizes typical flare stack or tank vent "wet" gas liquids. The remaining conditioned gas is OEM spec fuel for on-site generation equipment or delivers a clean burning flare. Power use includes site needs, grid sales, or data operations. Valuable condensate is monetized and engines run optimally.

Condition injection gas:
The Micro Refrigeration Unit strips liquids and conditions injection gas for optimal results. Monetize condensate while improving injection gas. Results include better injection performance and fewer downhole equipment issues caused by condensates.

Feature overview:
- Minimal package footprint with compact, engineered components
- Simple, durable refrigeration system, serviceable by HVAC technicians  
- Refrigerant is safer than propane, reduces on-site hazards
- Low temp. separator (LTS) for improved separation
- High quality, common brand component metallurgy and trim

Liquid Recovery Unit-30 HP-New
Designed for 1-2 MMSCF/d total gas flow and +- 150 Bbl/d of liquids recovery
Note: 
This skid flowrange variance is composition dependent and requiries verification by OilPro's process engineering team.
This option deletes the 5 HP upstream dehydrator section for cases where initial dewatering is not required or when higher methanol injection rates are acceptable.

Summary:
-40 deg F capable system

Skid Mounted, c.w.:
 Inlet coalescing vessel c.w.
  Filter

Packaged with single controls:
 30 HP Compressor c.w.
 - Two stainless steel heat exchangers
 - Liquid dump valve
 H2S compatible materials
 2" SCH 40 inlet and outlet piping for gas
 1" SCH 40 Product outlet 

Electrical:
 Single Phase
 480 Volt

Major Component Description:
AC-1000: Refrigerant Condenser
 1/2" tubing c.w. 
 fins for optimized heat dispersion

V-1: Inlet Knockout/Coalescer combination vessel
 Custom sized for application.
 MAWP: 245 psig @ 250 deg F
 MDMT: -40 deg F @ 245 psig
 Coalescer, custom design
 ASME Sec. VIII Div. 1 design
 NB Registered, CRN for Canadian applications

C-100: Refrigeration Unit
 Scroll compressor
 MAWP: 415+ PSIG @ -40 deg F
 Refrigerant 448A
 30 HP/ ??A/ 60 Hz/ single phase

V-100: Receiver:
 Sized for application
 MAWP 450 PSIG
 6' x 18"

E-1: Gas/Gas Exchanger
 MAWP: 675 PSIG
 design rate to match process conditions
 316 SS construction

E2: Chiller
 MAWP 675 PSIG
 316 SS construction

E3: Pre-Cooler
 Liquid to gas exchanger (Refrigerant)
 MAWP 675 PSIG
 tube and tube configuration

V2: Cold Separator
 875 PSIG
 ~24" x 6' s/s
 304 SS tubes, 0.125" walls

Customer to supply:
1. Two-phase separator
2. Cold Weather Enclosure
3. Methanol supply, pump and storage
 - Methanol Injection Pump
 - MAWP 1500 psig
 - ~20 USGPM/d capacity
 - 120VAC
4. Product storage tank
5. Outlet filter
 -mounted to skid c.w. bypass, filter element.

Show Less

Inlet filter 6" x 6' s/s

Mounted to 5 HP refrigeration skid c.w.
Tangential Inlet from refrigeration section
bypass pre-piped c.w. block valves
filter element.

Connections:
A420-WPL6 Flanges
Filter Element Closure:
6" 150 RFWN
6" x 2" 150 ANSI RFSO Conc. Reducer
Inlet:
2" 150 RFWN
Outlet:
2" 150 RFWN

Assorted:
A350-LF2 Smls Fittings
A420-WPL6 Fittings
A106-B SMLS Fittings

Above welded with ASME compliant QC/QA
Vessel is built as a fitting

Valves:
One :
1" 3000# NACE, Low Temperature Ball Valve
Two:
1/2" 3000# NACE, Low Temperature Ball Valve

Internal:
One 6" x 36" Coalexcing Filter element c.w. Two Garlock gaskets

Show Less